Help me with rebuild aspire ready coile please

[New smoker]

Hello i saw many people in you youtube rebuild the ready coiles from aspire and another company,s after it burned i try to do it but my coile gives me not the sam ohm on the original coile

Please help me i try to rebuild
aspire coil bvc with (kanthal 1AWG 28 not 26 ) with (normal cotton) it work for 2 minutes and burned then my aspire zelos mod tells me no atomizer ! How can i build it please with the sam ohm 0.7 watt 18 up to 23 only , the burned coil gives me 2:00 ohm and some 1:88 1.8 ohm i just need it it sam the aspire coils 0.7 ohm watt 18 up to 23 watt only my tank is (Natules 2) 3 ML

Please check the attached picture i want my rebuild coile work like this because it make my battery work for a long time

My kit is aspire zelos it works fine with me. This man rebuild it good


And afew Arabian channels successd to rebuild it.

 

[93gc40]

Steam-engine.org. will give all answers

Sent from my SCH-I605 using Tapatalk

 

[Izan]

Hello i saw many people in you youtube rebuild the ready coiles from aspire and another company,s after it burned i try to do it but my coile gives me not the sam ohm on the original coile

Please help me i try to rebuild
aspire coil bvc with (kanthal 1AWG 28 not 26 ) with (normal cotton) it work for 2 minutes and burned then my aspire zelos mod tells me no atomizer ! How can i build it please with the sam ohm 0.7 watt 18 up to 23 only , the burned coil gives me 2:00 ohm and some 1:88 1.8 ohm i just need it it sam the aspire coils 0.7 ohm watt 18 up to 23 watt only my tank is (Natules 2) 3 ML

Please check the attached picture i want my rebuild coile work like this because it make my battery work for a long time

My kit is aspire zelos it works fine with me. This man rebuild it good


And afew Arabian channels successd to rebuild it.

View attachment 696441

Practice, Practice, Practice.
About the 10th or 15th time you do it, it may be close to perfect.
Use the zelos to adjust your wattage up or down depending on the resistance of the coil you build.

Best of luck
I

 

[New smoker]

I try with the kantal 1AWG 28
With normal cotton it gives me bad taste and the ohm is very high sometimes 2.0 ohm it makes the mod and tank hot and make the battery drain faster i think its bad idea to rebuild this ready coils or I think I should use jabaness cotton

 

[sonicbomb]

Backwards engineering a factory coil is challenging, maybe consider getting an RTA and take rebuilding to the next level.

 

[Paul Mohr]

I have tried it 4 or 5 times. My advice, don't bother. Can it be done? Sure, like you have seen people do it. Is it easy and worth the headache, nope, not in my opinion. Building a coil is not hard to me, I have built thousands over the years. But I have yet to rebuild a "prebuilt" head and have it be worth the effort. Especially with the aspires.

I may try to rebuild the 3 coil head in my new aspire athos though. It looks like it might be easy to do.

I agree with Sonic, if you want to build just get a RTA and have at it. You won't be sorry.

I also have a kanger subtank mini and that come with rebuild section, or you can use pre made coil heads.

 

[New smoker]

Thanks for advices

 

[mcclintock]

If you look at the original BVC coils, they use wires with non-resistance leads and the junction is down within the coil itself, the last wrap on each end is not heating and just acts to form the cotton, and the junctions between the insulator and the legs are also not heating. The NR wire will probably still be shiny while R wire is black. People have been replacing NR-R-NR type coils with regular wire a long time, but I wouldn't recommend it and doubly so with these chimney-type coil head structures.