Holla All Vapers..

[RinGGo]

Hi, I'm new here, need advise from all vapers..

Just start vaping about 2 month..

My Mod currently is Ecig Joyetech with Aga-T+ tank..

Can I know that Aga-T+ is suitable for Ecig or not? Or maybe I have done a wrong setting at my tank..

The smoke not too much and sometimes I have a burn taste.. My backup tank is RDA tank..

 

[Baditude]

I currently have two AGAT2 tanks. I use mine on a Provari and a Silver Bullet. I'm extremely happy with mine, although it took two wicks and three coils to get there. There is a large learning curve involved with these. I spent a number of hours trying to get it working well to my satisfaction.

What are you using for your wick material and what guage of wire for the coil?

Have you checked the coil for it's resistance, or ohm rating?

At what voltage are you using from your battery?

Are you tilting the mod horizontal while you vape to increase juice wicking?

Do you have the air hole in the cap lined up directly with the wick?

 

[RinGGo]

Hi Baditude,

I'm currently using Mesh as a Wick material, I don't remember what gauge of my wire but it a little bit thick..

My tank ohm now is 1.2ohm but it not fixed sometimes it change to 1.3ohm.. Before this it more unstable my 1st tank ohm is 2.4 but suddenly it's drop to 1.1ohm and getting up 1.4ohm, it always constantly changing.. I don't know why it like that..

For now I'm vaping only on 3.0v because if I rise the voltage I will get burnt taste.. But at the low voltage I don't have satisfaction when I'm vaping and also the smoke is little bit..

Yes, I tilting my mod when I'm vape to make sure my mesh wicking the juice..

Yup, I put the cap hole line up with my mesh..

Is it I have done something wrong with my tank?

Really need advise here..

Thanks..

P/S : Sorry for my bad writing in English..

 

[Baditude]

What PV are you using? Is it fixed voltage or variable voltage?

When the ohm is unstable, it often means there is a short somewhere. This could be as simple as making certain that the thumb screw on the positive post is tight, or the wick is touching the bottom of the tank or the positive post in the tank. Try spinning the wick inside the coils somewhat. More than likely though there is a short in the actual coil. This probably the reason you are getting a burnt taste at higher voltage, too.

 

[hausmouse]

Is your fill screw in or out? Take it out and throw it in a drawer. My wick is barely oxidized. Make sure you didn't roll it too fat so it's not too tight in the walls of the hole. Does it glow evenly with no juice on it?

 

[chefdaddy903]

It sounds like there's a short in the coils, they may just need a little playing with so that there all firing evenly.

 

[RinGGo]

Baditude : I'm using evic.. I will check my tank with your advise and will get back to you soon..

hausmouse : Is it ok to take the fill screw out? I thought my liquid will will flow out if I do that.. What's that means if my mesh still glowing eventhought with no juice?

chefdaddy903 : I always playing with my mesh and khantal everyday to make sure the ohm stable.. I'm really tired of this situation..

 

[hausmouse]

Take the screw out and tip it to that side over a bottle of liquid that you have in it. It won't come out. Tip it the other way you'll see the wick get really wet and drip if you hold it there. When your at this point fire and you should have no glowing. Put the cap on as you know how and tip and puff when you taste that the juice isn't harsh you can inhale.

With no juice in it it's definitely gonna get hot depending on the amount of power your using. It should be even. Some wicks will get red at the top first if they're cut but most should be even

 

[RinGGo]

Thanks hausmouse for your advise..

Now I get the stable ohm it's now 1.2ohm..

I vape with my ecig at 3.0 volt..

I feel better now vaping with my aga-t2 tank..

Thanks all.. I will update more later..

 

[hausmouse]

Thanks hausmouse for your advise..

Now I get the stable ohm it's now 1.2ohm..

I vape with my ecig at 3.0 volt..

I feel better now vaping with my aga-t2 tank..

Thanks all.. I will update more later..

Absolutely and just for reference on my 1.5 I've gone up to 4.8, not saying you have to go up higher and I forget the evic specs so I don't know how far you can go but if your looking for more at any point don't worry about it just make sure you tilt because it will use the juice on the wick faster. Enjoy your renewed vape

 

[RinGGo]

hausmouse,

I not really confident to increase my voltage because I'm afraid my mesh will fast drying and I will get burnt taste.. Hehe..

But sometimes I will increase the voltage to have a deep taste of my juice..

 

[hausmouse]

Don't worry about it. If I'm gonna go outside my comfort zone I keep a drink next to me and do a stupid tilt. I look rediculous but its my best defense. And I don't inhale the first so if all else fails the bad taste is only in my mouth and easily rinsed. Also best on a full tank. I've gone up that high but now I just relax on 4.3 at 1.4 so I don't have to pay attention too much

 

[billybob4315]

LOL ^^^^^^ nice