How to USE (enter info) Ejuice Me up calculator

[Red_Bird]

Theres an updated version of ejuice Me Up I've heard, but I've used this version so often I'm just used to it.

FOR THE LADY THAT PM"D ME SHE COULDN"T MAKE 100% VG using ejuice me up:

E juice Me UP can't magically convert your PG flavorings into VG. Whatever the total flavoring % is (the sum total of all flavors) is the AMOUNT YOU ENTER for PG% at the bottom if you are trying to make all VG eliquid using PG flavorings!!!!!

So, if your flavorings total 20% at the BOTTOM AREA you enter:

80% VG
20%PG


Then hit bottom right TAB "Calculate".......If you can't follow these step by step instructions please just buy ejuice from vendors.

 

[Starlight 1818]

Here's how to enter info into EJUICE ME UP:



Top line (nic Strength e juice)= ENTER pg/vg ratio of ur nic and MG strength (aka...the nic u bought)
Second line (Target Strength)= ENTER the MG strength of eliquid u are making
Third line (Amount to Make)= ENTER amount you are making, __mil
Water/Vodka/PGA (Adding any additives? Enter the percentage here if so__%

Flavor #1.....= ENTER the % u are using
Flavor #2....= ENTER the % u are using
Flavor #3.....= ENTER the % u are using
Flavor 4......= ENTER the % u are using

BOTTOM SECTION= change 50% PG 50% VG to the ratio u are creating (if its not a 50/50 mix ur making)



----> hit bottom right TAB "Calculate"

*****the exact amounts u need to the tenth of a milliliter will now be revealed ( the amount of nic, pg, vg and each individual flavoring )

Got all that but, what do you put in the third box after the PG/VG % then another box for % again. What do i put in this box and what is it the % of

And is there a way to add 10% PG for flavor with 0% VG ? As that's what my flavoring is no VG added at that point.

 

[DeeDee1234]

The third box I belive is the amount of liquid your going to make
The flavor % lines are for the % of each flavor to add. They default to pg for flavoring. Only change the flavoring % if you have a vg flavoring this is very incommon.

The bottom section near the pg and vg totals is where you enter the % of pg and vg you want to make

 

[DeeDee1234]

Third box on the top line is the % of nic you have. Ie 100% pg 0 VG 48mg/ml
Third line is the amount you want to make 10 ml

 

[oldbikeguy]

That still doesn't tell me how to fill in the "drops per ml" section of the calculator.
If I put the PG count in (23) then it's wrong for the VG drops per ml count (14) and the flavoring at (32) drops per ml.
So I guess I have to run each recipe 3 times, changing the counts to get the correct recipe amounts
Right ?????

I use drops I just change the number in the little box for each ingredient and I keep a list in my cookbook

 

[Starlight 1818]

Third box on the top line is the % of nic you have. Ie 100% pg 0 VG 48mg/ml
Third line is the amount you want to make 10 ml

Yes this is true but i am talking about the sorry forth box on the same flavor line last one is % (of what i am trying to figure out)?

 

[DeeDee1234]

The flavor lines - the defaulf is 100% pg , on the far right enter the percent of flavor for each flavor in the mix. enter as many flavor lines as you need for that recipe.


drop count - most people use a average drop count for the three flavor,pg abd vg

If you use ml, you will not need the drop count

 

[vernhall]

So, I can use syringes to measure ... but... how do I use the calculator now.

That's simple -- just use the 'ml' reading shown on each ingredient... The 'ml' will not vary as 'drops' will since you're using a known measure rather than a guesstimate...

 

[Starlight 1818]

The flavor lines - the default is 100% pg , on the far right enter the percent of flavor for each flavor in the mix.

So if it is just 1 flavor then put 100% and if 2 flavors i put 50% in both boxes

Another question why is it when i try to add 10% PG to my flavor it always configures the VG as well. When i don't have VG in my flavor? I get how it would work with PG/VG flavor but not PG alone

 

[DeeDee1234]

The pg and vg sections in the flavor line are for the flavor itself. If the flavor was 50% pg and 50% vg you can enter it thier. The majority of flavors are pg and pg is the default on that line for this program. flavoring is listed as a percentage of the whole. For the example that I have been working with you enter 10 in the flavor % box. Because we were talking about a 10% flavoring recipe. This program will figure you pg/vg ratio, the nic and flavor to add to a given sample that you are making.


If you want to enter two flavors
Strawberry at 7%
cream at 4%

On the first flavor line enter strawberry and on the far right box enter 7%
On the second flavor line enter Cream and on the far right box enter 4%

 

[Starlight 1818]

Got it now TYVM DeeDee1234 you have been very understanding, patient and very helpful i am now ready to try it out with my next order

 

[DeeDee1234]

Got it now TYVM DeeDee1234 you have been very understanding, patient and very helpful i am now ready to try it out with my next order

Contunue playing with the calulator. Changing the values around. Adding more flavors at differnt %. change the pg/vg values of your final mix to get really comfortatable with the calulator and how it works.

Then get a spril note book and write down some recipes from that section and enter them in the calulator.

Use the notebook for the recipes you like and all the recipes you make. take notes as you mix and as you vape each mix. That way you will be able to check your notes to see what you want to change on your next batch

 

[Lina]

A quick question I make 120ml batches at a time... is it ok to use 20% Distilled water or is that too much? I use a nic base of 48mg and so much VG that my juice has always been really thick so I started cutting it by using distilled water... any thoughts? Thank you in Advance!