I just ordered 1

Status
Not open for further replies.

kas122461

Vaping Master
ECF Veteran
Jun 15, 2013
5,211
30,630
63
Indiana, USA
I have no will power, I just spent a hour an a half on the provape site, I made up a list, of what I would want, if I was going to buy one.
At the end of my whole process I placed my order, I am weak!
I know I will be happy though, here is what I ordered :

1 Provari V2.5 base model silver
2 IMR 18490 AW batteries
1 extended end cap for 18650 batteries
2 18650 2000 mah battieries
1 pila ibc 4 stage charger
1 pila 12 volt car adapter
1 Tatroe provari wide end cap w/spring
And 1 tube of Noalox thread lube

(That's aprox $360.00)
Hopefully I will have it by next week end
 

Baditude

ECF Guru
ECF Veteran
Apr 8, 2012
30,394
73,076
71
Ridgeway, Ohio
I have no will power, I just spent a hour an a half on the provape site, I made up a list, of what I would want, if I was going to buy one.
At the end of my whole process I placed my order, I am weak!
I know I will be happy though, here is what I ordered :

1 Provari V2.5 base model silver
2 IMR 18490 AW batteries
1 extended end cap for 18650 batteries
2 18650 2000 mah battieries
1 pila ibc 4 stage charger
1 pila 12 volt car adapter
1 Tatroe provari wide end cap w/spring
And 1 tube of Noalox thread lube

(That's aprox $360.00)
Hopefully I will have it by next week end

You obviously had done some homework. You got absolutely everything that I would have suggested for the ultimate Provari setup. Now all you might need to add at some point would be a beauty ring to top off the Provari.

Grats on a job well done! :headbang:
 

kas122461

Vaping Master
ECF Veteran
Jun 15, 2013
5,211
30,630
63
Indiana, USA
That's what I was intending to do today, when I started to make a list, it was all over, just had to have it. I was originally going there to look at the mini, which I still want! but that's another month.


I keep going there and leaving without buying anything, I am sure that will change one of these days.
 

Baditude

ECF Guru
ECF Veteran
Apr 8, 2012
30,394
73,076
71
Ridgeway, Ohio
Beauty ring? the only thing else I was considering to put on top of this, was one of those fluid flask mods. Just because they look so cool!
I am just not to sure of a tank made of this PETG resin stuff. I wish they would have made it out of pyrex.


You can see the Pro Rings (beauty rings) between my two Provari's and AGA tanks. They are used purely for aesthetics to allow for a clean straight line between the Provari and a juice delivery device.

I would have strong reservation about using any tank that uses polycarbonate or the PETG tubes, but that's just my preference. I would rather use a tank that I don't even have to think twice about what flavors that I can put into the tank. Plus, its an extremely expensive tank. I can purchase 3 - 4 IBTanks for the price you pay for a Fluid Flask.
 
Last edited:

kas122461

Vaping Master
ECF Veteran
Jun 15, 2013
5,211
30,630
63
Indiana, USA
I was just reading up on the beauty rings, and I like what I see so far, another item for my list. So the rings do not really screw on? they are just held in place w/ the tank? I will have to look up IBTanked, they do look good. I guess I just like the look of the flasks, cool scroll work. Makes it look like a piece of art, but I didn't buy it to just look a.t :)
I only have protanks right now, I haven't tried anything else yet so IBTanked I guess is a good place to start, I really am just looking at glass or pyrex tanks, I prefire pyrex.




You can see the Pro Rings (beauty rings) between my two Provari's and AGA tanks. They are used purely for aesthetics to allow for a clean straight line between the Provari and a juice delivery device.

I would have strong reservation about using any tank that uses polycarbonate or the PETG tubes, but that's just my preference. I would rather use a tank that I don't even have to think twice about what flavors that I can put into the tank. Plus, its an extremely expensive tank. I can purchase 3 - 4 IBTanks for the price you pay for a Fluid Flask.
 

pmg1944

Senior Member
ECF Veteran
Verified Member
Mar 22, 2013
90
36
Las Cruces, NM USA
@kas122461 You will be very satisfied with your purchase i did almost the same order 6 weeks ago took 4 days to get to me. Its turned into my daily driver it goes everywhere with me now my other stuff gathers dust except for a BAM I got used off the classies i got a Segeli clone kick for it and its awesome as well.

Enjoy your Provari !
 

kas122461

Vaping Master
ECF Veteran
Jun 15, 2013
5,211
30,630
63
Indiana, USA
Well that's interesting it has made my pro tank a tighter draw, I like it. Now I know what those Tatroe extensions are for, just makes me wonder why provape doesn't sell them? I also see what everyone is talking about, this thing is heavy for its size. I think it will fit in my mag light holser, the battery's are smaller then I thought they would be also. I also like being able to take a longer draw off of it, no 10 second cut off, 16 seconds is much better for me, I think. I am going to want one of those extensions, and also some of the tatroe tank's, and I think also the ebaron dripper pro. If i get those I think I will be set, wow I really does give a good vape, its a good thing I am sitting down, I think I am a bit light headed. :)
 

serenity21899

Vaping Master
ECF Veteran
Verified Member
Jan 18, 2013
6,322
11,254
Antioch IL
Beauty ring? the only thing else I was considering to put on top of this, was one of those fluid flask mods. Just because they look so cool!
I am just not to sure of a tank made of this PETG resin stuff. I wish they would have made it out of pyrex.

DSCN0783.jpg

I have a Fluid Flask. It is wider that the top of the base, so the ring hides that. Yes, I also need to dust, but that is another issue. :)
 
Status
Not open for further replies.

Users who are viewing this thread