- Status
I would like to know how he rewicked it as well. On my chip coil, the holes were not lined up exactly with the coil itself. I ended up not bothering and just tossed it.
So I rewicked the RBA head and this time I bent the wick tails up out of the coil collar and trimmed it so the tails was poking out about 1/4 inch above the top of the coil. Then I tucked the wick into the wick channels and so far after 4 tanks of juice, no leaks at all and it is wicking well. When I tucked the wick into the wick channels, I also used my ceramic tweezers to spread out the wick by going from the outside of the coil to ensure that the wick was filling the entire channel.
Hi jseah,cool that's great news my friend am glad it's working great for you,am really looking forward getting this bad boy,it should be in the next couple of days (I hope) I paid extra for dhl out of China from everzon I have used them in the past and I can guarantee they're great customer service,my rep is Trae,if you email him he always replies back and as helped me out many of times which is a rare thing these days,since you've been successful with you're wicking would you mind sharing what kind of coil you used jseah? Size,ohm,ect,thanks bud;-)
Oh by the way sorry my pic is upside down guys lol,I can't figure out how to flip that sucker right side up
I fed the wick through a juice hole, then through the coil, then up and out. Then I cut it off and extended both tails above the collar and cut them off. Then I pushed them down against the juice holes. Not to difficult but not as easy as a subtank mini v2 rba or protank. I did however overwick and will have to reduce the wicking density to obtain peak performance out of the chip coil. There's really no reason these coils shouldn't chain vape at 100w. I'll crack the code eventually.
26 gauge SS 316L, 8 wraps, 2.5 mm diameter coil. With dual coils, it measured out to be 0.27 ohms.
I noticed that the juice holes on my coil was not aligned with the coil. I did place an order for 3 packages of the prebuilt 0.3 ohm coils, but they are in preorder, so hopefully they will be available soon. I do have a spare, but I was saving it since the last coil lasted me only 4 days, but I was using it a lot. Next time I will give it a shot at rewicking it.
Thanks for all you're post regarding this tank guys,jseah where did you pre order your pre m'aid coils from?
Cigatron keep at it bud,I have no dought that you'll get that thing to perform exactly like you want it too 
We only get 1 pre made coil in the package no? The reviewers also stated that original packaging would include notch coils but from what I've seen that's not the case either,which leads me to that black plastic drip tip,how lame is that thing,they should have charged us an extra .50 cents and included that chuff cap that looks cool as hell imo,I can't even find a place that as those accessories in stock 
Thanks wworrells,yes I did but I get all my stuff from everzon kuz they have better prices,last I checked I think they have the tornado nano for almost 10 bucks less then heavens gifts and there shipping and customer service is AWSOME check them out bud
Hey jseah what wattage and temp do you run that set up at please? Am new to tc I actually got a roll of ss 316 26 gauge wire along with my nano tank so when it all arrives it will be my first tc build so am a little stressed out
I pre-ordered the prebuilt coils from Heaven Gifts. They're $10 for a package of 5, but because I ordered it during their Dragon Boat Festival sale, I got 15 percent off. With the 26 gauge SS316L, I am vaping it at 40 watts. I've tried it as high as 50 watts, but once I started going above that, I could tell that the wicking is starting to not be able to keep up. I am using it on a Sigelei 213, and in TC mode, it was setting the starting wattage at 56 watts, and then when I'm vaping it drops down to around the 26 watt range. I like a warmish vape, so typically with TC coils I will set the temp around 480-500, but with the SS coil on the Sigelei 213, I set it around 520. This is a little bit higher than with my other SS TC mods, like the Cuboid, that I set at 500. With SS, I still prefer wattage mode rather than TC mode. In power mode, you get a consistent vape. In TC mode, when TC kicks in, it "feels" like it isn't working (you don't get the audible clue of a sizzle on the coil), even though it is and is still producing vapor.
Thanks a lot jseah I really appreciate it,can I bother you to ask if you are spacing your coils or just tight wrap ? I also could have sworn I saw in another thread that you also purchased the chuff cap for that bad boy! If so where did you get it? I want one badly cause I think it looks better but cannot find them anywhere?
Thanks as well for sharing your tc experiences,I think I'll try it out in wattage mode as you suggested,does ss wire vape as well as kantal in power mode?
Prior to companies coming out with TC profiles for SS, SS was used in power mode. Honestly, I cannot tell the difference between vaping using SS or kanthal, however so people do say that SS has a cleaner taste?
The package didn't include spare notch coils, it included a pair of twisted coils for the RBA head.We only get 1 pre made coil in the package no? The reviewers also stated that original packaging would include notch coils but from what I've seen that's not the case either,which leads me to that black plastic drip tip,how lame is that thing,they should have charged us an extra .50 cents and included that chuff cap that looks cool as hell imo,I can't even find a place that as those accessories in stock
The juice holes didn't line up on mine either so I used needle nose pliers to turn the ceramic chip so they would line up horizontally. Vertically the holes will never line up. My little adjustment hasn't seemed to affect the res so far.
- Status
Similar threads
- Locked
