Received my 18350 today. Very impressed. The P+ is so nice looking and so much smaller than it looks in pictures. On a whim I purchased a 16340 last night and I'm very much looking forward to receiving it.
Incoming PrecisePlus Stock Status.
- Thread starter forcedfuel50
- Start date
- th_trl_thread_readers 0
- Status
I too got the 18350 today and super nice tube mod. I agree is is way smaller then I thought it would be. Slapped my Ody on top and the base gets a little too snug to the top of the mod. The draw is a little tight. Gunna play around with it and see what I can do. This thing is really nice though. Great button and exceeds the quality I was even expecting
Yes, you have to crank the Ody center pin out a hair more than you typically would for it to work best on a P+. For me it's a blessing, I find the Ody's draw a little too loose and I can get it just right on a P+.
Good call. When I first got they Ody I have to admit I thought it was a bit to airy but now I love it. I go to hit one of my favorite Cisco 1.5's and it feels like my skull is going to implode haha.
oder # 13032 I don't know why, buy just in case the Shockwave is too big for me I went back to where I started (but the plus version); a P10, six batteries and the nicest t-tip I have seen in a long time Kofun? Should be a great set-up (and no more springs melting on me daily) . I am excited !!!!!
I do have a question though, now that I am used to 18350 batteries will the smaller batteries have a lighter punch or just last me 45 min instead of an hour an a half (18350)?
I do have a question though, now that I am used to 18350 batteries will the smaller batteries have a lighter punch or just last me 45 min instead of an hour an a half (18350)?
I've never used the 10440 but I'm guessing they will work just as good but you'll just have to be swapping batteries more is all.
The world is a safer place.
Not a lighter punch, just a shorter one. Here's proof. I finally landed an inline voltage meter. In the top row of the picture below you see a 10440 loaded with an ICR 10440 battery. First picture shows the voltage output (battery very fresh off the charger, fired a couple times) without an atomizer attached - basically the voltage of the battery. Second picture shows the same thing except with an atomizer attached ready to vape. The reading on the meter at this point is called "loaded". So we have 4.18 volts unloaded and 3.68 volts loaded.
The bottom row shows the exact same thing with the same atomizer on a PrecisePlus 18650 with a 1600 mAh IMR 18650 battery in it. The readings are 4.16 and 3.51.
I'll let you ponder those results.
Yep. Just seconds later.This makes me want an inline voltage meter!
I admit the drop off under load of the 18650 seems kind of drastic. Did you use the same load?
I have no idea of the age or condition of the batteries. Just grabbed them from the pile.
Another variable is the condition of the mod I suppose. The 10440 is brand new yesterday, the 18650 has been around the block a few times and probably needs a good cleaning. But I think the point is illustrated.
Last edited:
The world is a safer place.
The bottom row shows the exact same thing with the same atomizer on a PrecisePlus 18650 with a 1600 mAh IMR 18650 battery in it. The readings are 4.16 and 3.51.
I'll let you ponder those results.
Snork you need some new batteries.... If I take a 18650 at full charge... 4.2-4.1 volts and put it under load it drops to 4.0-3.9 volts...
Yeah, I'm sure I do. That's the main reason I got the meter, to weed out some duds. Kinda hard to do blind.
[Edit: All my IMR 18650s regardless of age give similar readings with that particular atomizer. If I change loads to a different atomizer things look different. I don't want to hijack this thread so I'll do further research and ask questions about the health of batteries and all of this elsewhere.]
[Edit: All my IMR 18650s regardless of age give similar readings with that particular atomizer. If I change loads to a different atomizer things look different. I don't want to hijack this thread so I'll do further research and ask questions about the health of batteries and all of this elsewhere.]
Last edited:
The world is a safer place.
Not a lighter punch, just a shorter one. Here's proof. I finally landed an inline voltage meter. In the top row of the picture below you see a 10440 loaded with an ICR 10440 battery. First picture shows the voltage output (battery very fresh off the charger, fired a couple times) without an atomizer attached - basically the voltage of the battery. Second picture shows the same thing except with an atomizer attached ready to vape. The reading on the meter at this point is called "loaded". So we have 4.18 volts unloaded and 3.68 volts loaded.
The bottom row shows the exact same thing with the same atomizer on a PrecisePlus 18650 with a 1600 mAh IMR 18650 battery in it. The readings are 4.16 and 3.51.
I'll let you ponder those results.
Thanks Snork, shorter punch is fine with me that's why I ordered enough ICR's to hold me through the day (I think I ordered 5, almost enough if I'm home). A P19 battery will last me about 30 minutes with a 1.5 carto and constant vaping. Btw, did I see the illusive brass capped P10 plus in the picture? Nice. And thanks for your help.
Awesome, I've got the "I need a new mod" bug and love that two-tone look
Where should I watch for a heads up of when they're going up, this thread? and how long does stock typically last? I'm hoping it's not like sales of pretty much everything else I want so I can actually get a chance at one, but as long I know when they're going up and will be available at the time you can be sure I'll be ready ;-)
Awesome, I've got the "I need a new mod" bug and love that two-tone look
The Parts are done and we are now doing are part to fit, polish, assemble and test. I will begin by estimating the wait at about two weeks from date of order. I'll try to have them up on the site shortly and there are plenty to go around.
I was told last week about a week, so hopefully this week they will have a batch for me. I'll post up asap when i hear from them.
long shot but is it possible to have the old school "rounded" vent on 18350 for my 1yr not a single analog milestone please? 
- Status
Similar threads
