Indulgence Mt-Rta
- Thread starter 98ruby
- Start date
- th_trl_thread_readers 0
- Status
@MMW I tried out the single coil adapter tonight. I didn't do a new build, just took one coil out, so its a single 8 wrap 24g 3mm ID coil now. Running it around 35w, its working correctly, but I definitely prefer the dual coil condig, at least with this build. I think it could definitely be better with a nicer single coil build, parallel, twisted wire, fused Clapton, etc, but I was mainly trying it out for proof of concept.
Got mine today... Blows my Zephyrus away... Goes thru my juice like there is no tomorrow- all I gotta say is wow!
By any chance - anyone find out what size grub screws this monster can take?
Thanks in advance
Vape safe and support the call to action on casaa's website if you haven't done so ....
Oops- big thank u to Thunderdan gave the size m2.5x0.45 a couple pages ago
By any chance - anyone find out what size grub screws this monster can take?
Thanks in advance
Vape safe and support the call to action on casaa's website if you haven't done so ....
Oops- big thank u to Thunderdan gave the size m2.5x0.45 a couple pages ago
Last edited:
Dual 28g 8 wrap on a 3mm dia. spaced Ni200 working great for me. Ohms out at about .114 Ohms on my IPV 4s running 560f on 40j! MMMMMMMMM NICKEL!
What is your mod? I would suggest a dual 26g for starts. Let us know how it's going. Remember that this thing loves a nice wick!! Wooioooooo!
Boooooommm!
Had to ditch the stock drip tip... way to short for my liking. I got a wide bore friction fit Delrin once from Cherry vapes a while ago and love it. it is friction fit so there are no o-rings and because of that the inner bore is able to be wider. had it on my crown, but its now on my Mutation. I ordered a new one this morning so Ill soon have one back on teh crown. Really love the delrin tips as they don't get the lip funk on them.
What I found best for wicking was for coils that are 3mm wide, I cut a strip of KGD that is about twice the width of my coils, take the outer skins off (no clue if this does anything, its just my method to my madness), and gently roll it on my pants to make it a loose log. thread through the coil... Now here is where its different from MOST rda's, I have to have the cotton kinda tight in the coil.... then I wet the wick in the coil and about 3/4 inch past it both ways. using a bent paperclip I poke and prod the wet wick into the juice slots until they stay and I can thread the top on over the Deck. Snip the wicks about 1/16th or just a smidgen longer from the juice wells and then gently poke them back so they are flush with the edges of the holes. screw on the glass portion and fill it up. Haven't had a leak or dry hit when doing it this way.
The link for grub nuts on ebay; m2.5 grub screws in Industrial Supply and MRO Products | eBay. Looking for some USA shippers.
You should be able to get the screws at your local hardware store. I get mine from ace hardware
Sent from my Nexus 6 using Tapatalk
Sent from my Nexus 6 using Tapatalk
@EverPresentNoob, yep! That's pretty much the way I wick it. I don't roll it but everything else is spot on. It's definitely a lot easier to form in the channels when wet. It does like a nice wick!
So, you're digging the output?
So, you're digging the output?
I'm surprised they didn't have them. My local ace has tons of small screws, every time I've needed a screw ive been able to get it at ace
Sent from my Nexus 6 using Tapatalk
Sent from my Nexus 6 using Tapatalk
No, I hate the grub screws.
Sent from my Nexus 6 using Tapatalk
Sent from my Nexus 6 using Tapatalk
- Status
