That was what it was called when I first tried it. I haven't noticed a difference.
Indulgence Mt-Rta
- Thread starter 98ruby
- Start date
- th_trl_thread_readers 0
- Status
That was what it was called when I first tried it. I haven't noticed a difference.
Pretty quiet in here. 
Had time to rebuild the MT last night, this time I went with spaced SS316 dual coils, 7 wraps, 3mm ID, .20ohm. Hittin like a champ.
Now to build my other MT, might try Ti in it, mainly because I want to test Ti TC on the RX200, and partially because I haven't built anything with Ti in months, and I have a bunch sitting around.
Had time to rebuild the MT last night, this time I went with spaced SS316 dual coils, 7 wraps, 3mm ID, .20ohm. Hittin like a champ.
Now to build my other MT, might try Ti in it, mainly because I want to test Ti TC on the RX200, and partially because I haven't built anything with Ti in months, and I have a bunch sitting around.
Soooooo, my resistance jumped down to .38 after it had been chilling at .43 for 2 days......still vaping like a champ, will break her down later to see wsup
Good morning, everyone! I've gone through about 8mg of juice since building it yesterday late afternoon. It seems I am still getting just a slight trace of leakage in it. I packed in as much cotton as I thought was prudent, but maybe it still isn't enough. I'm going to be out most of the day, but maybe I'll break it down and redo the wicks and really stuff it tight. I am still in amazement at this tank. I just rebuilt my Clouper Z5 and what I thought was the best tank I've ever run into, wasn't. It's good, but the MT puts it to shame.
Didn't you build 2.5mm coils? Maybe try 3mm ID coils next time, wicked semi tight through the coil seems to be about the perfect amount of cotton for me with this RTA. No leaking while filling, or otherwise.
I was going to do that, but I was in such an all fired hurry to get it going, I had a bunch of 26g coils already wound in 2.5mm. That's my preferred build on all my RDAs. I'll wind up some 3mm coils and maybe go at it in the morning for another try. Will 24g fit in those little post holes? I guess they will. I'd like to build down to .25-.3. I'm at .27 right now and have it turned up to 60W and it's great.
I don't own any 22. Seems too heavy to me. I do have some clapton coming I'm anxious to try. I just got single strand 26/34, I think, just to try. I used to do a triple twisted 30, and that was good. Might make some more of that.
Yeah, after spending 10 minutes cleaning the wire, then it springs about all over the place on me. I've almost got it built now though, hopefully I did a good enough job though.
I've given up on ti, too. SS is so much nicer. As soon as I can I'm going to order a lot of it, including to make Claptons.
I have 2.5mm coils in one of my MTs. They've been in there since I got it (don't know why, but they're staying very clean!). Satan has 2.5mm Claptons, but those always expand a bit so they could be 3mm.
I have 2.5mm coils in one of my MTs. They've been in there since I got it (don't know why, but they're staying very clean!). Satan has 2.5mm Claptons, but those always expand a bit so they could be 3mm.
Dang it...after all that, got them installed, wicked, and went to do one last tighten down on the screws, and snapped a leg. I guess I'll try out the single coil adapter again..smh
OK GUYS & GALS MY LOCAL B&M SENT ME A NOTICE THEY'VE GOT REULEAUXS! DOESN'T SAY WHICH BUT I DON'T CARE! GONNA GET ONE!!!!!! I'm an instant gratification kinda guy so this is awesome! Hope they got the HG2s too! OMG! OMG! OMG!
run!OK GUYS & GALS MY LOCAL B&M SENT ME A NOTICE THEY'VE GOT REULEAUXS! DOESN'T SAY WHICH BUT I DON'T CARE! GONNA GET ONE!!!!!! I'm an instant gratification kinda guy so this is awesome! Hope they got the HG2s too! OMG! OMG! OMG!
- Status
