Indulgence Mt-Rta
- Thread starter 98ruby
- Start date
- th_trl_thread_readers 0
- Status
Looks like a knock off aromamizer to me. Not that it's a bad thing at all, the aromamizer is a nice rdta
Sent from my Nexus 6 using Tapatalk
Sent from my Nexus 6 using Tapatalk
Looks like an Aromamizer Smashed into a Bellus. Haha. Supposed to be Top fill, has a wide bore drip tip and comes with a 510 tip adapter.
It looks nice to me, I hated how small the tip was on the aromamizer. I've always used chuff caps on my rda so a wide bore is always welcomed by me
Sent from my Nexus 6 using Tapatalk
I've went a little overkill today. I got that facet injection @ 7am in my lower back and its killing me. So I've been a tad bit Vape crazy. I've switched the batteries out in the rx200 once already but I've been using my troll at 160 watts since I got home from the hospital. I'll probably be close to 60ml vaped today
Sent from my Nexus 6 using Tapatalk
Ok, folks, beware: lengthy post and NSFW coil porn.
Broke into the black MT today. Coiled SS316, dual parallel 26ga, 3.5mm ID, 5/4 wrap, .110 Ohms.
![20160108_180839[1].jpg](https://www.e-cigarette-forum.com/attachments/20160108_180839-1-jpg.521086/ "20160108_180839[1].jpg")
I did my previous wick just as I tried the first time:
![20160108_181537[1].jpg](https://www.e-cigarette-forum.com/attachments/20160108_181537-1-jpg.521087/ "20160108_181537[1].jpg")
![20160108_182129[1].jpg](https://www.e-cigarette-forum.com/attachments/20160108_182129-1-jpg.521088/ "20160108_182129[1].jpg")
And it flooded big time. So I tried again. This time I laid a strip of rayon on the deck and out the channels before putting wick in the coils, like this:
![20160108_185125[1].jpg](https://www.e-cigarette-forum.com/attachments/20160108_185125-1-jpg.521089/ "20160108_185125[1].jpg")
![20160108_185529[1].jpg](https://www.e-cigarette-forum.com/attachments/20160108_185529-1-jpg.521090/ "20160108_185529[1].jpg")
![20160108_185615[1].jpg](https://www.e-cigarette-forum.com/attachments/20160108_185615-1-jpg.521091/ "20160108_185615[1].jpg")
![20160108_185819[1].jpg](https://www.e-cigarette-forum.com/attachments/20160108_185819-1-jpg.521092/ "20160108_185819[1].jpg")
Now she doesn't leak, and she vapes like a beast! Running in TC mode, 450 degrees. I have her on the Koopor because the batteries for the RX aren't charged yet. Tomorrow on that. I've got bubbles and no dry hit yet. Almost vaped through rayon break in, so I will later comment on the flavor.
![20160108_191547[1].jpg](https://www.e-cigarette-forum.com/attachments/20160108_191547-1-jpg.521093/ "20160108_191547[1].jpg")
Broke into the black MT today. Coiled SS316, dual parallel 26ga, 3.5mm ID, 5/4 wrap, .110 Ohms.
I did my previous wick just as I tried the first time:
And it flooded big time. So I tried again. This time I laid a strip of rayon on the deck and out the channels before putting wick in the coils, like this:
Now she doesn't leak, and she vapes like a beast! Running in TC mode, 450 degrees. I have her on the Koopor because the batteries for the RX aren't charged yet. Tomorrow on that. I've got bubbles and no dry hit yet. Almost vaped through rayon break in, so I will later comment on the flavor.
S'what I thought. I wicked it the same as I did my first build; I had no problem with that one. No prob, I have it fixed for fair now. And as to homely, look again at the bottom photo of the tank assembled. They cleaned up just fineThose are some homely looking street walker wicks
Weird how it flooded brother.
You guys are a bad influence 
I purchased my Rx200 and Mutank thanks to you guys.....and LOVE them both! Best mod and tank I've owned to date.
I ran the factory prebuilt coils for a few days, not bad. I then rewicked the factory coils with Rayon...better.
For the last week Ive been running the RTA with dual 8 wrap (each) Nichrome 80 around. 3mm...have tried several wicks....organic cotton, KGD, Cellucotton, and currently Cotton Candy. I will give a slight nod to both the Cellucotton and Cotton candy for easy of wicking, flavor.
Still trying to tweak my builds as I'm getting some leaking when I first fill...and some slight weeping after. My juice channels are about as full as I think they could be...but will try a bit more this evening.
One other addition...added a 2puffs drip tip and wow!! Even bigger clouds...have the perfect set up!! Thanks for all the input!!
I purchased my Rx200 and Mutank thanks to you guys.....and LOVE them both! Best mod and tank I've owned to date.I ran the factory prebuilt coils for a few days, not bad. I then rewicked the factory coils with Rayon...better.
For the last week Ive been running the RTA with dual 8 wrap (each) Nichrome 80 around. 3mm...have tried several wicks....organic cotton, KGD, Cellucotton, and currently Cotton Candy. I will give a slight nod to both the Cellucotton and Cotton candy for easy of wicking, flavor.
Still trying to tweak my builds as I'm getting some leaking when I first fill...and some slight weeping after. My juice channels are about as full as I think they could be...but will try a bit more this evening.
One other addition...added a 2puffs drip tip and wow!! Even bigger clouds...have the perfect set up!! Thanks for all the input!!
Welcome @bluesbishop! Leave your wallet at the door! The advice is great here and the influence is bad!You guys are a bad influence
I ran the factory prebuilt coils for a few days, not bad. I then rewicked the factory coils with Rayon...better.
For the last week Ive been running the RTA with dual 8 wrap (each) Nichrome 80 around. 3mm...have tried several wicks....organic cotton, KGD, Cellucotton, and currently Cotton Candy. I will give a slight nod to both the Cellucotton and Cotton candy for easy of wicking, flavor.
Still trying to tweak my builds as I'm getting some leaking when I first fill...and some slight weeping after. My juice channels are about as full as I think they could be...but will try a bit more this evening.
One other addition...added a 2puffs drip tip and wow!! Even bigger clouds...have the perfect set up!! Thanks for all the input!!
Oh, well done! Welcome to the club. You may not have noticed yet, but your life has changed forever, lol...You guys are a bad influence
I ran the factory prebuilt coils for a few days, not bad. I then rewicked the factory coils with Rayon...better.
For the last week Ive been running the RTA with dual 8 wrap (each) Nichrome 80 around. 3mm...have tried several wicks....organic cotton, KGD, Cellucotton, and currently Cotton Candy. I will give a slight nod to both the Cellucotton and Cotton candy for easy of wicking, flavor.
Still trying to tweak my builds as I'm getting some leaking when I first fill...and some slight weeping after. My juice channels are about as full as I think they could be...but will try a bit more this evening.
One other addition...added a 2puffs drip tip and wow!! Even bigger clouds...have the perfect set up!! Thanks for all the input!!
Their account balance is gonna change hanging out with us lol
Sent from my Nexus 6 using Tapatalk
Ok as promised. Top view side by side. Also thought I'd mention seems the v deck has the same thin o ring the standard deck does so swaping the thin o ring for the beefer stock coil o ring. Also the airflow holes on the v deck are visually smaller then the standard deck for mine. 
I've got a friend that drips 12mg everyday on a mech mod. It's crazy
Sent from my Nexus 6 using Tapatalk
Sent from my Nexus 6 using Tapatalk
Thanks..lol..been a member of ECF for several years...post in burst...sometimes not for a year or more...but...always reading.
This is my 6th sub ohm tank/ RTA...and love it...flavor is as good as dripping.
Ordered the velocity deck , a bag of o rings...and a back up RX200 in black as a back up...will probably order another Mutank as well.!
- Status
