innokin mvp 2.0

[UrKillingMeSmalls]

I rotate my wicks every 2 to 3 days. I wash them put them in vodka over night. I then rinse them off and the next day I dry burn them. Just pulse them for 3 sec or so look down the tube and when they turn red they are ready just like any other atty.

Ive washed them before but a couple times got some bad taste after. Does it matter what vodka you use? Dark Eyes is dirt cheap.

The wire that comes with the kayfun (clones) is 32 ga. I found it a bit thin. I've been using 28 ga on a 3/32 drill bit (2.38mm) with 10 coils for about 1.6-1.8 ohms. Seems to be the sweet spot for me and my Kayfuns. Here's a good site to help you figure out ohms (or get you more confused )

Coil wrapping | Steam Engine | free vaping calculators
(check the tabs as there's other useful info on the site)

LOL. Ill bookmark that site for sure. The 32 is way to thin. Im going to try wrapping on the 3/32 like you said. Rubyroo does it on a 5/64 bit for 1.2-1.4ohms.

Check the bottom of your kayfun. There's a screw there that you can loosen 1-2mm to get contact on the MVP. I have no issues with my KFL but my 3.1 had the same issue you did (reading "non"). Also, if you clip the excess wire, it could fall on the base, connecting the pos and neg posts and cause a short (again, reading "non").

I was unsure if the contact screw feature was also on the KFL+ or just the KF+. So much confusing stuff hehe. I also think I have "gear acquisition syndrome". Thanks for all the advise!

UPDATE: Got a 1.8ohm coil rolling right now. Its fluctuating though between 1.8 and 2.0 ohms on the MVP v2. What wattage do you vape these coils at KTMRider?

 

[Mrdaputer]

Ive washed them before but a couple times got some bad taste after. Does it matter what vodka you use? Dark Eyes is dirt cheap.




LOL. Ill bookmark that site for sure. The 32 is way to thin. Im going to try wrapping on the 3/32 like you said. Rubyroo does it on a 5/64 bit for 1.2-1.4ohms.



I was unsure if the contact screw feature was also on the KFL+ or just the KF+. So much confusing stuff hehe. I also think I have "gear acquisition syndrome". Thanks for all the advise!

UPDATE: Got a 1.8ohm coil rolling right now. Its fluctuating though between 1.8 and 2.0 ohms on the MVP v2. What wattage do you vape these coils at KTMRider?

Did you rinse off the vodka let dry before dry burning?

 

[KTMRider]

UPDATE: Got a 1.8ohm coil rolling right now. Its fluctuating though between 1.8 and 2.0 ohms on the MVP v2. What wattage do you vape these coils at KTMRider?

8-9 ohms works great for me. I played with 7-15 watts on both MVP and Vamo V5.

 

[RonSwanson972]

Kanger is ok. Go rebuild able and support a local shop they will help a lot.

 

[UrKillingMeSmalls]

Did you rinse off the vodka let dry before dry burning?

I would just rinse them off, let them dry and about 50/50 they were good or gross. I never dry burned the enclosed attys by kanger. Just the single coils, the ones with the flavor wick on top. I'll probably get some vodka and try this if it comes up. I'm liking the single coil rebuilds Im doing right now in the kanger protank attys and I have enough 32g kanthal and cotton to last at least a good 5-10 years

Im liking the build I did on the KFL+ clone also, but its not very tasty but vapor is alright. Probably just have to play with it some more. Could also be the juice, its max VG, think he said something like 90/10 or 80/20 vg. Might try some 50/50 from local b&m.

 

[UrKillingMeSmalls]

Mrdaputer: So on rotating these closed coils I would rinse them off with tap water, let dry and then soak overnight in vodka. Then id let them rinse in filtered water and dry them off completely before dry burning. Seems to be MUCH better. Ill use this on my nephews coils to get more life out of them thanks a bunch!

KTMRider: Im LOVING this KFL+ clone. Have you tried a chimney coil build? I'm thinking about trying the second coil build here:

https://www.youtube.com/watch?v=z7o7RFoTtw0