I prefer springs, but can manage fine as long as its adjustable. I've had a couple attys that prefer adjustable pins over springs. My Lemo for one can get a bit goofy with a spring, as can my eXpromizer. My SquapeR did also.
IPV D2 announced.
- Thread starter Completely Average
- Start date
- th_trl_thread_readers 0
- Status
absolutely roxy. I cannot believe they are actually going to supply this with a slotted pin after all of the previous hurt and busted 510s with this issue.....
im not sure this fills me with joy. Looks like the Ni calibration is way out. It barely singes the cotton at 550F. This is not right and looks a little like the experience people are having with the istick TP device....I fear the Ti might be even worse...It will work I guess but be prepared to be vaping at much higher 'tempereature' on this than you would on a DNA40 or whatever..
ps. it a little better than the eleaf which doesnt burn at any temp up to 600F! At least in the reviews I have seen...
The lack of any liquid triggers the dry coil condition, so it won't burn the cotton. At most it will singe it, because there is a slight delay before the chip can respond to rapid escalation in resistance and turn off power. In other words, it's working as it should.
You can see the same test down with the SX350J here, same result - it doesn't burn the cotton, rather it triggers the dry coil condition as it should (well, until he puts it into power mode that is
):
Last edited:
The lack of any liquid triggers the dry coil condition, so it won't burn the cotton. At most it will singe it, because there is a slight delay before the chip can respond to rapid escalation in resistance and turn off power. In other words, it's working as it should.
You can see the same test down with the SX350J here, same result - it doesn't burn the cotton, rather it triggers the dry coil condition as it should (well, until he puts it into power mode that is
so he starts to see singing at 420F which makes sense, not 550F on the D2 which is my point!!!!!! This would suggest that the D2 is over 100F out of whack....The devil, my friend, is in the detail!
ps. I know how TP is supposed to work
Last edited:
That's Danish, which is only barely a language. Sorry my Danish friends
Sent from my C6903 using Tapatalk
so he starts to see singing at 420F which makes sense, not 550F on the D2 which is my point!!!!!! This would suggest that the D2 is over 100F out of whack....The devil, my friend, is in the detail!
ps. I know how TP is supposed to work
In the IPV D2 video, he uses a coil with about twice as many wraps, which means that it takes longer for the coil to heat up. So I'd say you can't make direct comparisons of the two videos as result.
i disagree. It either regulates at the correct temp or it doesnt! There is no earthly reason one should have to revise target temp dependening on how the coil is made - just the final resistance and the wire material. Im not saying the D2 should behave identically to the sxm or anything else but it should be a lot closer than that!
The earliest time I saw for delivery time on ebay was July 30 but it looks like they are in stock which means 101 is shipping them out. So I figure we will have them by the end of the week
latest estimate now has moved to 31st July for mine in UK. Dont really know why I am surprised.
Correct temp isn't the most relevant factor here. It's rather how quickly the chip can detect a dry coil condition and cut off power that matters. That means one's Joules setting and coil resistance matter quite a bit more (as well as the chip's measuring frequency). Thus, the higher the Joules setting, the more power that'll get thrown at the coil before cutoff, increasing the risk of cotton singe. The opposite is true as the resistance increases.
Something I have noticed. Some units go down to 5 Watts other down to 7 Watts...
5 Watts
7 Watts
5 Watts
7 Watts
Hi Yoz, still not clear what you are saying here. Do you mean that at low resistsances, the chip is unable to respond quick enough to temp/resistance rise at low coil mass but as the coil gets bigger and resistance higher, then this effect is reduced??
cheers
steve
Like it will be shipped then or you should have it in hand by then?
In video one above this guy says firmware upgrades are gimmicky and unnecessary…WOW, what a knucklehead.
I think it was a ridiculous comment trying to justify the fact that the IPV D2 is not firmware upgradable. It's not like anyone would force his upgrade-adverse customers to upgrade if the option was offered and they didn't want to.
If they have continued their Design feature set, it is Spring loaded and the Slot is for air flow on Bottom open devices. Yea, a few still exist - lol
All 101 says now is it's back up but it says 7 22 update manufacturer still hasn't shipped them to us but we will tell you when next week. Well it's 5 days later and people on ebay already have them.
- Status
Similar threads
