Ithaka new rebuildable part
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
- Status
xtreme - yeah I was thinking about getting one of those, too. I might be stopping at Michael's today and if I see one I will pick it up. I think the 1.5mm bar would be best for me, too.. that's the closest to 1/16"
How tight can you get the coils with that gizmo?
And I just figured most people probably have a drill handy, so that could be used in a pinch at least!
How tight can you get the coils with that gizmo?
And I just figured most people probably have a drill handy, so that could be used in a pinch at least!
Even better then! I will def get one. Hopefully I can find one with good mandrel sizes. At least the 1.5mm is good! I would like 1.5mm and 2mm at least, I think?
I suppose in the worst case scenario maybe I could put blunt-tipped needles (of the size I want) over a smaller mandrel?
Thanks aalwani~ I should have pointed that out. But I did want subver to see it with the modification.
Didn't realize and just got this kit. The mandrel that was suppose to be 2mm is measuring 1.8mm. So now I am wondering if the kit that comes with the 1.5mm may also be less. The Deluxe Kit comes with the built-in table-mount base and the 2 rod set does not.
Artistic Wire Coiling Gizmo Deluxe Winder ~ 5 rods, 4.5mm, 4mm, 3mm, 1.5mm, and 1.0mm
Artistic Wire Coiling Gizmo Econo Winder ~ 2 rods, 3mm and 2.0mm
Thanks guys! I just got home from Michaels, I got the deluxe kit 
can't wait to try it out!
can't wait to try it out!
why not iwrong? But later buddy. I did my best by making almost all the spares for previous GG items and now I have to start making Proteus
Does anyone put cotton into the metal cup to soak up flooded juice?
Sometimes when it floods and I turn it upside down like I would normally do, a ton of ejuice comes out. I'm still getting used to the setup and have been reducing floods, but I just wanted to check and see if extra cotton from the channels to the bottom of the metal cup would reduce this or change the vape at all.
Thanks guys!
Sometimes when it floods and I turn it upside down like I would normally do, a ton of ejuice comes out. I'm still getting used to the setup and have been reducing floods, but I just wanted to check and see if extra cotton from the channels to the bottom of the metal cup would reduce this or change the vape at all.
Thanks guys!
Yes extra cotton would help. I was thinking of doing it but my cup rarely fills up with juice. If it does it means you're opening the mouthpiece too much.
Be careful you don't want too much cotton because it might end up disrupting air flow.
Yeah it's definitely from opening too much.. I guess I'm still finding my sweet spot. Might give the extra cotton a try though, I'll let ya know how it works
Sure do.
I was opening it up too much as well but I've found that if you use Mr Krinkle method you don't need to open it up so much.
I was opening it up too much as well but I've found that if you use Mr Krinkle method you don't need to open it up so much.
I've been using mr krinkle method as well. I have been opening the mouthpiece about 2 turns, sometimes 2 and a half.. Under that I start to taste cotton (not burning at all, just a slight taste like it's not saturated)
My juice is about 80+ VG so it's a little thick
My juice is about 80+ VG so it's a little thick
This is exactly the same issue that i am getting. My coil is at 0.5ohms, if i opens too little, cotton taste if too much flood. So i play around with tilt and juice control to lessen this issue. I am using 100% vg.
Sent from my iPhone using Tapatalk
- Status
Similar threads
