Ithaka official

[yankeebobo]

Is this juice a different pg/vg ratio? Is this burnt taste right away from the first pull? There are some good ideas here that have been posted.

Try after setup, vaping it without the tank in place. Treat it as a dripper. It'll help make you conscious of how many pulls you can get on how many drops. After a while, you can put the tank back on and adjust the mp accordingly. That juice may need wide open, closed, etc despite what the basic feed is at.

 

[gdawg]

the burnt taste is right away.. i ve tried dripping n its still burnt. i m using a single coil x set up. next i going to try opening the basic feeding fully, but then i m sure it wld overflood n start leaking and gurgling!!

 

[gdawg]

i ll also try wrapping the coils loose. i ve always wrapped the coils very tight as suggested by imeo in his video.

 

[yankeebobo]

Snug is good. Too tight and it chokes. Also, I've had inconsistent results with the X using a single coil. Now I only use X for dual coils. Try a single coil with the wicks running side by side instead of crossing.

 

[imeothanasis]

I still suggest tight coils dg. Your issue is because only some coils light to my opinion. The rest of your coils maybe touch somewhere. Better make a new coil and use 2mm wick. If you have a 3mm wick then remove 2 strands of it

i ll also try wrapping the coils loose. i ve always wrapped the coils very tight as suggested by imeo in his video.

 

[yankeebobo]

If this is high or pure VG, tight doesn't work. VG has a hard time climbing and keeping up the wicking. Higher PG wicks better for sure.

 

[B4DJ1N64N]

I've read somewhere about ithaka gurgling problem, my question is: I ordered an ithaka from COV yesterday, will I get the revised version or the first one (the gurgling one?)

Sent from my mind using the Force, or mindmelt, or whatever..

 

[subver]

I've read somewhere about ithaka gurgling problem, my question is: I ordered an ithaka from COV yesterday, will I get the revised version or the first one (the gurgling one?)

Sent from my mind using the Force, or mindmelt, or whatever..

Yup it will come with the new nut. i honestly didn't get the gurgling issue with the old nut either way, though. Maybe once or twice but it wasn't an issue for me.

 

[imeothanasis]

We have different results yankee but if loosy coils work better for you with VG then no problem. Whatever works for you buddy

If this is high or pure VG, tight doesn't work. VG has a hard time climbing and keeping up the wicking. Higher PG wicks better for sure.

 

[Icig]

I think I received the small nut when my tele mouth piece came in. Can anyone post a photo of it so I can confirm. I will throw it in next time I rebuild to hopefully rid of the gurgling. Even though it does not bother me much. Though, the cone of air reaching the coil instead of the cylinder seems like it would do better.

 

[xtreme101]

I think I received the small nut when my tele mouth piece came in. Can anyone post a photo of it so I can confirm. I will throw it in next time I rebuild to hopefully rid of the gurgling. Even though it does not bother me much. Though, the cone of air reaching the coil instead of the cylinder seems like it would do better.

small center post top nut

 

[yankeebobo]

We have different results yankee but if loosy coils work better for you with VG then no problem. Whatever works for you buddy

Different results for sure. But just to clarify, not loose. Just gently squeezing the wick snug. Loose is NO good

 

[imeothanasis]

yes, lose coil always bring burn taste to me yankee. I agree about the right way to make coils around wick.

 

[LongDraw]

I tried the search feature but can't find the circumference and/or diameter of the ithaka air control ring. Trying to find it as I am having a leather case made and since it is slightly bigger than the provari and the ithaka want to make sure it is accounted for.

Thank you

 

[gtbb]

I measured 24mm on mine.

 

[Guts]

Hi guys, do you know if the SS window for Ithaka works with the UFS too? I think I'll grab another one because I'm planning to get a UFS when the preorder will start ^^

 

[imeothanasis]

thats right gtbb[QUOTbE=gtbb;10359386]I measured 24mm on mine.[/QUOTE]

 

[imeothanasis]

no guts, sorry buddy

Hi guys, do you know if the SS window for Ithaka works with the UFS too? I think I'll grab another one because I'm planning to get a UFS when the preorder will start ^^

 

[Guts]

Thank you for your reply Imeo will you make some for the UFS in the future? I like to see the level of liquid but I also like to know that I can switch to a SS window if the plastic one breaks.

 

[Killjoy1]

EDIT: gah, replied before noticing there was another page