Ithaka official
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
-
- Tags
- provari
- Status
It would be neat if all of the correct guesses in the December contest got a chance to reserve one of these. I bet you would see some wild guesses.
So the only pieces I will need to purchase are the mouthpiece and new rebuildable part for the new Ithaka? Will Bruce have these on his site?
Sent from: The Land of Tortuga!
Sent from: The Land of Tortuga!
Aww I am so excited I have been slowly collecting the pieces to build one of these specifically.
Sent from: The Land of Tortuga!
Sent from: The Land of Tortuga!
A cloner in Xiamen is looking at this picture and crying into his glass of baijiu.
You can tell how excited imeo is about this piece, he actually screened Vasilis' call!
While I have a Tsaf and love making wires, I can see a very big demand for R-only attys done properly. Other than the Spheroid, I have found other R-only devices were very finicky for my tastes. If the build was off by a tiny bit, if your wick was 0.5mm too high or too low, you got flooding and leaking or dry hit syndrome.
I wouldn't be surprised if all future GG attys were released in R-only and R/NR editions.
I wouldn't be surprised if all future GG attys were released in R-only and R/NR editions.
Oh my word, my mouth literally hit the floor! I am very happy using nr wire in my builds now that I have the hang of it and even built my own wire wielder. I do recall reading many many posts where people wanted to use resistance wire only. I always thought that nr wire would be necessary for gg atomizers but I stand corrected. Another fine feat of the great GG engineering. Imeo you are always looking out for us, now everyone can be happy. You truly stick to your signature below every post you make, "I will satisfy every vaper out there". Great piece of work Imeo, you rock!
I think this will be a beautiful addition to the Ithaka! I had a MISTer and loved it to death...but it wasn't GG lol. So now I will have the best of both worlds in Just GG
Sent from: The Land of Tortuga!
Sent from: The Land of Tortuga!
Looks great Imeo. I too hope they aren't sold out before I can get my hands on one with only 500 pieces made.
Just a couple simple questions.
1 You showed a plastic piece in the video that goes on the positive post's post so that it won't ground out against the negative post's will this be included or did you decide it wasn't needed?
2 How much distance is there between the top of the post screws and the underside of the inside of the mouthpiece? I ask because I am hoping people that use thicker wires (28 maybe even 26 awg) won't have an issue where either 1 the mouthpiece won't screw all the way down or 2 they will get a short because the mouthpiece is touching the posts.
Just a couple simple questions.
1 You showed a plastic piece in the video that goes on the positive post's post so that it won't ground out against the negative post's will this be included or did you decide it wasn't needed?
2 How much distance is there between the top of the post screws and the underside of the inside of the mouthpiece? I ask because I am hoping people that use thicker wires (28 maybe even 26 awg) won't have an issue where either 1 the mouthpiece won't screw all the way down or 2 they will get a short because the mouthpiece is touching the posts.
Oh wow... like WOW!!!
I nearly sold my last Ithaka ... something kept telling me to keep it. Now my prayers have been answered. Here we go...
Thanks Imeo.. so many people are going to go nuts for these parts.. 500 might not be enough.
I'm buzzing.
I nearly sold my last Ithaka ... something kept telling me to keep it. Now my prayers have been answered. Here we go...
Thanks Imeo.. so many people are going to go nuts for these parts.. 500 might not be enough.
I'm buzzing.
Thank you fright my good friend.
1. I will include the plastic you say, to be more safe
2. distance between the top of the post screws and the underside of the inside of the mouthpiece is 0,7mm. But even if you use a 1mm wire, the wire cant touch the underside of the inside of mouthpiece because wire sits on the side slots that are 3mm deep. So the real distance between wire and underside of the inside of mouthpiece is about 2,5mm
Thgank you my good friend Skiba.
500 pieces is nearly nothing, its just an experiment to see if GG people like it. Then we can make more of it
500 pieces is nearly nothing, its just an experiment to see if GG people like it. Then we can make more of it
500 pieces of that genius "simple coil" and "microcoil heaven" (as aalwani said) upgrade... will last only one or two days!!!
Imeo get ready for more immediately
Imeo get ready for more immediately
It will last 2 hours Stelios, not 2 days. But lets see how people will like it and then we can make more
Guys, I have to tell you that I made this upgrade only because some people like it. But you have to know that making a wire is not that easy as on original Ithaka and that applies to all atomizers without NR wire. But I think you know that already. The only good thing to my opinion is that we have liquid control that is really needed on all tankomizers. Tankomizers cant work as you like without liquid control.
- Status
Similar threads
