Ithaka official
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
-
- Tags
- provari
- Status
Lesson learned: As an FYI, it is possible to tighten the rebuildable part too much. I split the fat little o-ring by tightening too much against the base 
On the plus side, I had a spare from some Ody parts and took the opportunity to zap-weld some 0.6 ribbon and wrapped a single coil "X" (~1.1Ω using 1.5in res ribbon). I'll run this build for a couple tanks but so far not liking it as much as a dual coil "X" done with 1.5Ω ready wires...
On the plus side, I had a spare from some Ody parts and took the opportunity to zap-weld some 0.6 ribbon and wrapped a single coil "X" (~1.1Ω using 1.5in res ribbon). I'll run this build for a couple tanks but so far not liking it as much as a dual coil "X" done with 1.5Ω ready wires...
GGTS and Stealth will not be sold via preorders icig my friend. So better order your Ithaka and you can order your GGTS when it will be available
Lesson learned: As an FYI, it is possible to tighten the rebuildable part too much. I split the fat little o-ring by tightening too much against the base
On the plus side, I had a spare from some Ody parts and took the opportunity to zap-weld some 0.6 ribbon and wrapped a single coil "X" (~1.1Ω using 1.5in res ribbon). I'll run this build for a couple tanks but so far not liking it as much as a dual coil "X" done with 1.5Ω ready wires...
I've been running this setup for single coils (0.6 ohms) lately. Best method for single coils that I've tried thus far. Three wicks under the coils and I have yet to get a dry hit.
Attachments
this ithaka comes with a plastic middle tank.
which is the part i need to order to make it a full stainless steel tank?
i worry some of my juice may crack the plastic.
which is the part i need to order to make it a full stainless steel tank?
i worry some of my juice may crack the plastic.
The stainless steel section (to replace the clear window) is not ready yet, but Imeo will make it for sure
In the meanwhile, if you have an Odysseus short mode, you can use its tank section on Ithaka.
I also have 1 zapper that should arrive in the next few days. I hope it will work so I don't have to use ready wires.
Lesson learned: As an FYI, it is possible to tighten the rebuildable part too much. I split the fat little o-ring by tightening too much against the base
On the plus side, I had a spare from some Ody parts and took the opportunity to zap-weld some 0.6 ribbon and wrapped a single coil "X" (~1.1Ω using 1.5in res ribbon). I'll run this build for a couple tanks but so far not liking it as much as a dual coil "X" done with 1.5Ω ready wires...
Today's setup is single coil:
2 strands removed from a 3mm wick, so we have 2 wicks 2mm each. Put wicks side by side and put the wire very tight on them. Put wick on channels as usual. The result is thicker vapor and a change on taste. If you think that Ithaka tastes great, try this
2 strands removed from a 3mm wick, so we have 2 wicks 2mm each. Put wicks side by side and put the wire very tight on them. Put wick on channels as usual. The result is thicker vapor and a change on taste. If you think that Ithaka tastes great, try this
Last edited:
Today's setup is single coil:
2 strands removed from a 3mm wick, so we have 2 wicks 2mm each. Put wicks side by side and put the wire very tight on them. Put wick on channels as usual. The result is thick vapor and a change on taste. If you think that Ithaka tastes great, try this
Trying this tonight!!!
Today's setup is single coil:
2 strands removed from a 3mm wick, so we have 2 wicks 2mm each. Put wicks side by side and put the wire very tight on them. Put wick on channels as usual. The result is thicker vapor and a change on taste. If you think that Ithaka tastes great, try this
Going to have to try this.
Today's setup is single coil:
2 strands removed from a 3mm wick, so we have 2 wicks 2mm each. Put wicks side by side and put the wire very tight on them. Put wick on channels as usual. The result is thicker vapor and a change on taste. If you think that Ithaka tastes great, try this
what resistance are you using this at, sounds like i will have to try this on my next build. i just preordered another ithaka that i will use to try many setups and will have the one i own now for everyday use.
I got a spark-o-matic from Pancho on VP. It's really fun but the "ZAP" always startles the bajeezus out of me (and the dog...)
Hey there Vapor2112, I have tried it and I have to say it is more fuss than it is worth, it is very difficult to work with and frays instantly when you cut it badly.
It was definitely not a win for me.
Hope this helps my Friend;
Sincerely;
Nate
It works as usual on higher ohms. Even at 6 volts the behavior is as it was. We just open a little more the mouthpiece
Haven't touched the stuff yet, but I've been hearing great things using it in genesis devices, just haven't really heard much chatter yet in anything else.
I ordered some of the 1/32 diameter and will give it a go in the Ithaka for grins. I'll report back when it arrives.
I ordered some of the 1/32 diameter and will give it a go in the Ithaka for grins. I'll report back when it arrives.
- Status
Similar threads
