Ithaka Upgrade Kit .. When ? and another question
- Thread starter tarricone
- Start date
- th_trl_thread_readers 0
- Status
Also curious about when and if cov will be getting them, e smoke guru's credit card handler doesnt accept payment from illinois for some reason...
i could bank transfer but I dont think thats worth the 35 dollar fee from my bank haha
i could bank transfer but I dont think thats worth the 35 dollar fee from my bank haha
Last edited:
e-SmokeGuru will do PayPal
I have also had problems trying to get MoneyBookers to accept payment
I have also had problems trying to get MoneyBookers to accept payment
When trying to use the upgrade kit on a ggts just using the ggts base I am encountering a problem:
The center pin of ggts fits inside the center post of the upgrade kit blocking airflow, so although electrical connection is being made you can't vape it.
Am I doing something wrong?
The center pin of ggts fits inside the center post of the upgrade kit blocking airflow, so although electrical connection is being made you can't vape it.
Am I doing something wrong?
GGTS's pin is 3mm fat and the slot of the new Ithaka part is 2mm fat, so its impossible for GGTS's pin to go inside Ithaka's pin grate. What I can think off is that GGTS center post is off center, so better change your o-rings inside
..........
Welcome in our forum nel... You're upgraded now... but there is no popcorn for you
Just tried it, it is impossible to get in with the brass post screw. Without the screw It goes in barely at the tip but airflow still can go in obviously because of slots in pin. So slots in pin are not completely covered. Airflow is affected a little to half I think.
Is there supposed to be something on the end of the center post? Mine is internally threaded, but there is nothing in/on the end.
Pics in one sec.
PS - I wish this word "impossible" would stop being used. It is pretty annoying to have a number people asserting that I have magical powers
when I clearly don't.
Pics in one sec.
PS - I wish this word "impossible" would stop being used. It is pretty annoying to have a number people asserting that I have magical powers
when I clearly don't.
Last edited:
lol, its impossible only on paper. In reality all are possible grate
as xtreme said, you miss the small AD brass pin that goes inside the brass threated part
as xtreme said, you miss the small AD brass pin that goes inside the brass threated part
Is there supposed to be something on the end of the center post? Mine is internally threaded, but there is nothing in/on the end.
Pics in one sec.
View attachment 289164 View attachment 289165 View attachment 289166
PS - I wish this word "impossible" would stop being used. It is pretty annoying to have a number people asserting that I have magical powers View attachment 289167 when I clearly don't.
Is there supposed to be something on the end of the center post? Mine is internally threaded, but there is nothing in/on the end.
Pics in one sec.
View attachment 289164 View attachment 289165 View attachment 289166
PS - I wish this word "impossible" would stop being used. It is pretty annoying to have a number people asserting that I have magical powers View attachment 289167 when I clearly don't.
with impossible i meant for me
So I have 3 Peny v3 and have bought many extras to try and get one of my internals to fit my ithaka however when I go to screw in the updated internals ( I have added the longer positve post and brass long nut) it won't screw all the way into the ithaka's juice control ring. It gets stuck on the derlin big flat insulator. Any suggestions on what I'm doing wrong? Does the ithaka use a different internal housing ring then the Peny v3? Because on the website the are the same price and look the same but unlike other compatible parts they don't say "Penelope v3/ithaka"
Oh and since the derlin doesn't go past the juice flow control ring the whole internals are raised making the 510 connection not possible with the a/d pin
- Status
Similar threads
