What store has all parts for the eRoll available *and* in stock? Sucks to get juices one place, bottles from another, cones from another, tanks from yet another....
- Status
The crux of the problem is that your preferred juice is the most important component there. If they don't sell the eRoll parts as well, then well.. you're stuck buying those elsewhere.
That said, I buy my juice from Wordup-Ecig, and they have the parts in stock as well. They don't have the best prices I've seen for the eRoll parts, but they do have an always-available 5% off coupon and free shipping, which can offset the cost if you're buying small quantities at a time.
Seconding Wordup Ecig, the prices dont bother me when they have the best juice money can buy, and usually with the free shipping i end up spending the same as i only buy little bits at a time!
Wordup doesn't have the black cone- does anyone know if there's any problems fitting a chrome onto a black eRoll setup (besides it looking goofy?) I know there shouldn't be a problem, but....
There is no problem. The only difference is the color -- I've mix-and-matched them all. But yeah, it'd look a bit goofy lol.
Yeah i thought it would be cool so i was playing with different colors ( i have 1 of each color complete) and it didnt really look good on any
Only other combo that actually looks good, imho, is black tank on white cone/battery. I still prefer the clear tanks though as my eyesight isn't the greatest.
Goofy maybe, but you will be able to find it easier. I have the same problem with my black blu. Because its black I lose it all the time.....
I've only had leaks for two reasons. First I got some knockoff attys and the spikes are thinner so they leak. Second I've done some SS wicks that were a little looser than needed. They didn't really leak, more like flooding the atty. Once it floods they don't lean out the rest of the juice.
I made a wick from 28 mm long piece of mesh (#500), but its last 1 mm is only 14 mm(which is against the coil).
So it is not too loose to leak. But still not give a dryhits, because its thin head.
Also condensation and a burbling sound is reduced for that.
I do not know if it works at all times, but least this one works very well.
I've never had a problem with my Ego-C leaking either, and many complain of that. I never take the end caps off to refill and make sure the tank is all the way on... clicks.
If I leave the Eroll on the table with a full tank, sometimes there is a thin line of liquid on the table under it, but not what I would call a leak.
If I leave the Eroll on the table with a full tank, sometimes there is a thin line of liquid on the table under it, but not what I would call a leak.
Ah, hold up. Maybe we should define 'leak' here then. That's actually what I've been calling a leak on mine -- the thin line of juice. I only get this if I close the PCC for > 30 min or so. I've taken to simply leaving it open as much as possible. This isn't a problem at home and at work, where I'm typically sitting at a desk, but on the go it is slightly annoying. Not enough for me to write off the eRoll (I just wipe it off with the bottom of my shirt), but annoying nonetheless.
The replacement tanks and atties I got from Good Prophets are working in both my eRolls with no leaking ever. The same with tanks/attys I got in a coop. If someone is seeing leaking with a new atty and/or tank they should contact their vendor.
Ok ive been over this. Ive filled my cart until there were no air bubbles, and had a line in the case. No air bubbles in the tank. Device was sitting on a shelf constant temperature.
Its condensation in my case from inside the cone and cartridge.
Its condensation in my case from inside the cone and cartridge.
Last edited:
That would be a leak. Mine don't leak. If yours leak you got bad tanks I guess. I think you should get some more and see if that fixes the problem.
Not saying you're wrong, but.. I've been through about 30 tanks now and they all do this if I leave the PCC closed with the eRoll in it for > 30 min. Some worse than others.
Yes, I could have gotten a bad batch since I bought most of them around the same time. But it does mean there is some variability in quality control here.
On mine, it's not. It's eliquid -- it's pretty easy to tell since it leaves my hands feeling oily if I grab it without checking it first.
If I got 60 bad tanks, that's fine.. it wasn't that much money.. but the ones from my kit did it as well.
Incidentally, mine don't leak when left outside the PCC, like you stated. They only do it if I put it in the PCC and close it for a length of time (e.g., put it in my pocket).
The vapor left in your tank area and cone are pg/vg, its still eliquid basically in texture. It collects in mine, and that tends to leak out a tiny bit.
- Status
Similar threads
