Can someone tell me how wide the flat part of the top around the 510 is
please say 20mm
If that's the case ill be ordering one of these to put my Killer 705 and D-Base tank I just ordered on.
Kamry K100
- Thread starter Revoke
- Start date
- th_trl_thread_readers 0
-
- Tags
- evic fasttech myvaporstore vamo
- Status
Man that would be awesome cause I think this would look great on it
http://a248.e.akamai.net/origin-cdn...yzu/v/vspfiles/photos/D-BASE-4.jpg?1362904856
http://a248.e.akamai.net/origin-cdn...yzu/v/vspfiles/photos/D-BASE-4.jpg?1362904856
Thanks so the taper will be about 18mm then I guess. That shouldn't be too bad.
I've had a Crown sitting around for like a month that I won and I'm looking for a telescope to put it in as well so ill probably grab a K100.
I've had a Crown sitting around for like a month that I won and I'm looking for a telescope to put it in as well so ill probably grab a K100.
The K100 has a floating center post. So all you have to do is screw your atty all the way down, then screw the battery tight and anything will sit flush.
Kind of ish? It's a Killer 705 from Leo. It's a rebuildable dripper that you can use in dripping mode or put in a tank. So it's like an amp tank in as much as its an atty in a tank , but its silica/cotton etc based wick with a coil instead. If you go to the RBA forum there's a massive thread on it. Also like an AMP tank they're hard to get lol, I managed to snag one from esmokerIreland this morning , and I bought the tank and drip tip you see there from GreekVapes. Hopefully the wife lets me order a K100 next month, the setup as you see it in that picture was about 180 CDN all in.
What kind of 18350's are you guys using? I dusted off my old roughstack shorty. I tried some old Trustfires that were also dusty. For some odd reason I get better flavor from them . I'm also clueless about how low (resistance) can I go with the trustfires on the K100.
Okay all you K100 owners maybe you can help me out. I bought the kit that came with the small and big battery and charger with two cartos. I've been running the evic up to now but I've noticed a couple of odd things. I'm not experienced with mechanical mods so maybe this is just normal.
The grey 18650 battery it comes with (2000mah) doesn't give me much vapor or throat hit and the little battery (900mah) although still 3.7v gives me even less. If I put in the Samsung ICR-18650-26F I get great throat hit and vapor. Is this common with different batteries or does it sound like there may be something wrong with mine? Also I've charged the little battery all night and the light on the supplied charger never goes green. I don't know if it's the charger or battery or just me as I have no other charger to use on the small battery.
I've basically just decided to use my samsung batteries in it but that kind of leaves me short on my evic.
The grey 18650 battery it comes with (2000mah) doesn't give me much vapor or throat hit and the little battery (900mah) although still 3.7v gives me even less. If I put in the Samsung ICR-18650-26F I get great throat hit and vapor. Is this common with different batteries or does it sound like there may be something wrong with mine? Also I've charged the little battery all night and the light on the supplied charger never goes green. I don't know if it's the charger or battery or just me as I have no other charger to use on the small battery.
I've basically just decided to use my samsung batteries in it but that kind of leaves me short on my evic.
Buy some protected AW or EFEST IMRs. First off you want protected batteries , which the batteries that come with evics arent. They will also have a higher amp limit which means more wattage , which means more of a hit and more vapour.
I tried the Efest IMR, and the battery got hot as HECK ! I'm using .8 ribbon, so the resistance is super low. I threw in a AW IC 16340. All is well now. The vapor is HUGE !!!
I didn't bother buying the kit, just the PV. Those batteries that come with the kit aren't worthless, but they are crap (snf shouldn't be used on a mech) compared to what we have available. Mech mods should always be used with high drain IMR batteries. Protected ones if you don't know what you're doing, unprotected work fine but you should have a knowledge base to ensure you are using them safely. IMR Li-mn chemistry by itself is categorically safer than Li-ion, but a dead short will ruin anyone's day regardless of battery if you aren't prepared.
The light on the charger didn't go green because the battery is cheap. It probably won't reach 4.2v, might only achieve 4v so it isn't telling your charger to shut off.
My Magno looks so good on the K100. I built a 6 wrap .8 ribbon Kanthal coil. .9 ohm. Very satisfying vapor. Hangsen RY6 never tasted this good
Use IMR batteries in mechanical mods ... they can handle the higher amp draw. Those ICR batteries will work just fine in most regulated devices though (since most have amp limitations at or below the max amp output of an ICR).
- Status
