KangerTech SUBTANK Mini
- Thread starter Vap0rnomics
- Start date
- th_trl_thread_readers 0
- Status
Sweet-vapes sells them individually. According to their site they should have them mid march for all subtank varieties.
http://sweet-vapes.com/clearomizers-cartomizers-tanks/kanger-92/kanger-subtank/subtank-o-rings.html
I got the 4 pack because impatience, and they were cheap enough I didn't mind.
I have the blue on my nano.....
The purple I don't really get, I would have rather seen a true white along with a few more base colors.
Don't know why it kept the old photo below??
Attachments
Last edited:
If you don't mind me asking, who makes those drip tips? Do they fit well without wobble or springiness?
Last edited:
Drip Tip Designz.
They fit very snug. I was worried about how far down they would sit, but they sit flush.
It was weird, when I received the white and black one, the black would not fit on the ST I had the black o-rings in, but it fit fine in the ST with the clear o-rings. The white drip tip fit fine in both?? Easy enough fix, I just swapped the o-rings, but it still puzzles me why it didn't fit in that specific tank. Nice drip tips though, not so run of the mill, but a bit pricey.
Where's you leak coming from? How long have you had your stm?
KangerTech has the orings in stock, or they did yesterday, ordered blue for my full size ST and mini and a set of black for mini, as my last mini only came with red orings.
I agree on the blue, wish they was more of a royal blue, but at least they are doing a blue though, both my full size ST and one of my mini's are on blue mods, so want them to match
I agree on the blue, wish they was more of a royal blue, but at least they are doing a blue though, both my full size ST and one of my mini's are on blue mods, so want them to match
I'm getting about 70ml before having to change wicks and DB coil. I was getting 40ml or so when using max VG but I've switched back to 50/50.
wick maybe but coil, should be abe to just burn off gunk and rewick
Today is my 1st day on KST Mini, ,after being with Atlantis for almost 2 months.
I tried directly the RBA, and I love this one!!!
Just a small question,
My KST mini Driptip will fit OK in my Atlantis, but not the other way around. The Atlantis drip tip is like slightly bigger , so it wont fit the KST mini.
Is this common ?
I tried directly the RBA, and I love this one!!!
Just a small question,
My KST mini Driptip will fit OK in my Atlantis, but not the other way around. The Atlantis drip tip is like slightly bigger , so it wont fit the KST mini.
Is this common ?
yup, mini stmini tip fits in nautilus, albeit loose, but not vice versa.
the stmini has a slight smaller hole for tip than aspires specs
Well, I was hoping I had the leaking thru the air holes solved, but apparently not. I know everything inside is tight, I haven't had it apart since I re wicked it and made sure everything was hand tight. It was good for a few days, now it is gurgling when I take a draw on it, and leaking thru the air holes. I guess the final and last step is to take it apart again and replace all the O-rings. I hope that fixes it. I dunno, I don't think I'll be getting another one at this point.
Not sure what it does, but there is a clear o-ring on the 510 shaft (above the threads), is that one there?
I wonder if it could be wicking, bringing too much juice up on the deck, then travels down, to the base.
There is also a non replaceable o-ring inside the RBA chimney cap, that seals the air tube.
That's really odd, even a blank unbuilt RBA should seal without leaking. What ratio is your juice, PG/VG?
You aren't missing the top cap of the RBA or the little white o-ring inside the top cap are you? I forgot this once and it spilled juice out the air hole in a hurry.
Also check to make sure the little white o-ring seal is under the RBA, should be there above the 510 threading.
As a test just to see if it's something else.. use some cotton or something to plug the hole in the middle of the RBA deck, fill it with juice or water and see if it still leaks..
If you are talking about the o-ring inside the chimney that the shaft slips thru, yes it's there, and unfortunately, I don't see a spare o-ring in the bag for that.
- Status
Similar threads
- Locked