Yeah, that fiasco with the ProTanks burned me out as well... I'll never do another co-op.
Let's Talk Hardware
- Thread starter Pappy
- Start date
- th_trl_thread_readers 0
- Status
I think Papaw already has an RM4, doesn't he?You seek an Atomic BF atty grasshoppa..better known as an RM4.
Height: 24.3mm diameter: 19mm
I remember that one. Finally got em after much uncertainty and waiting. It was my last one too.Yeah, that fiasco with the ProTanks burned me out as well... I'll never do another co-op.
The positive screw is supposed to thread into the top insulator nut, then the first metal nut when tightened causes tension and keeps the screw in its place.
The threads on the insulator nut are stripped, this makes it so that the other nuts just pull the screw more and more and more through the Veritas and never really tighten fully.
Hard to explain but it makes it impossible to get things to stay consistent.
I just found some replacement top insulator nuts on the firefly website for $3 each. If I had known they were there before my account was tapped when I got paid Fri I would have ordered a few of them.
Sent from my Samsung Galaxy Note 3 using Tapatalk!
Ya, I'm not buying just one of them. Shipping is $6 lol
Sent from my Samsung Galaxy Note 3 using Tapatalk!
Yep, just gotta wait until next payday.Yep, gotta make it worth the shipping cost. A few of them ought to outlast you.
Sent from my Samsung Galaxy Note 3 using Tapatalk!
I'm a little surprised you were able to find replacement parts for your Veritas. Got a link to share with the rest of us Veritasers?
Yep they only have the insulator, they also used to have thumb nuts to replace the metal nuts but are sold out.
This is the official site for iHybrid.
http://www.fyreflyecigs.com/products/peek-insulator
Sent from my Samsung Galaxy Note 3 using Tapatalk!
At least they have them. It's a ripoff but they could probably charge twice that and still sell them to the desperate.
find out what thread they are and check out a local hobby shop that sells RC stuff....
Thanks for all of the suggestions. Chak, I had an RM5 (Double Cross converted to BF) but I traded that in one of my 'Shady deals' 
I remembered this morning that I have a $100 Visa my daughter gave me for Christmas to use on Vaping supplies. I still might go get that brass BF Cyclone w/ Cyclops AFC at Indy Vapors. I am also considering just go back to Rob and get an LP RM2 and either an RM3 or RM4. Heard a lot of good things about the RM4. Trouble is, Rob's site is like play land to me: There is a Grand rebuild kit, with video tutorial, for $25 where Rob shows how easy it is (for him) to switch an older Grand over to the newer contacts (Sparkey ?). Never hurts to have spare door magnets, juice well O-rings....
I have an older RM2 that I've kept as a spare. Today I decided to open up the air hole. I think the standard air hole is 1mm (pretty sure on that). Using a Variable Speed Drill set at 'crawl', I carefully opened the air hole to 1/16th (1.58mm). Whoa ! Talk about a big change form a small adjustment. Tons of vapor, makes the standard RM2 seem like sucking a dinner mint through a straw. Whatever loss of flavor, if any, seems minute. It's making my Kayfun seem weak, and only the Veritas comes close. I am not ready to drill all of my RM2's (YET....) but sure seems to improve what was already a nice little RBA
I remembered this morning that I have a $100 Visa my daughter gave me for Christmas to use on Vaping supplies. I still might go get that brass BF Cyclone w/ Cyclops AFC at Indy Vapors. I am also considering just go back to Rob and get an LP RM2 and either an RM3 or RM4. Heard a lot of good things about the RM4. Trouble is, Rob's site is like play land to me: There is a Grand rebuild kit, with video tutorial, for $25 where Rob shows how easy it is (for him) to switch an older Grand over to the newer contacts (Sparkey ?). Never hurts to have spare door magnets, juice well O-rings....
I have an older RM2 that I've kept as a spare. Today I decided to open up the air hole. I think the standard air hole is 1mm (pretty sure on that). Using a Variable Speed Drill set at 'crawl', I carefully opened the air hole to 1/16th (1.58mm). Whoa ! Talk about a big change form a small adjustment. Tons of vapor, makes the standard RM2 seem like sucking a dinner mint through a straw. Whatever loss of flavor, if any, seems minute. It's making my Kayfun seem weak, and only the Veritas comes close. I am not ready to drill all of my RM2's (YET....) but sure seems to improve what was already a nice little RBA
Or you can pick up a 1:1 clone from FT and skip the shipping . I grabbed one with the Aqua V2 , it's flawless and working perfectly . Built single 26ga 1 ohm coil , nice little atty . https://www.fasttech.com/products/3028/10008562/1816700-veritas-style-rebuildable-dripping-atomizer
Exactly , no concern if it screws up either , it's a helluva lot nicer than I expected though .
- Status
Similar threads
- Locked
- Locked
