Let's Talk Hardware

[Bronze]

What a great excuse to clean out the bottom of the vape box.

These are my little "memory box" contents:

View attachment 339376

Hey, aren't those the CE3's I sent you?

 

[Bronze]

Ce3s. Wow. I remember the day I was over them. Tossed one across an entire parking lot. Either they were amazing and a great vape, or they were dry hit leaking mother fraks

Sent from my SAMSUNG-SGH-I747 using Tapatalk

I still remember SteelJan reviewing the CE3's. She was an engineer and helped GotVapes design them. Over and over she would say, "And they don't leak!" "And they don't leak!" "And they don't leak!" It was irritating. She'd repeat it over and over. Well guess what...they leaked! Hahaha! Even funnier was she took these $2 cleaormizers and used them on a Darwin!

 

[DavidOH]

Had to make a trip to the B/M. My .4 build is really good but the sucker is hot with a normal drip tip. So another bit of shiny was needed. Much better. Still may need to get some lower nic.

 

[MostlySunny]

Omg David! That's so long!

(That's what you wanted me to say, right?)

 

[MostlySunny]

Hey, aren't those the CE3's I sent you?

You've always been good at keeping me on the cutting edge of things

Actually, I think I sent you mine because they were slightly possessed.

 

[76bridget]

Omg David! That's so long!

(That's what you wanted me to say, right?)

 

[DavidOH]

Omg David! That's so long!

(That's what you wanted me to say, right?)

I would never think such a thing.

 

[Bunnykiller]

Had to make a trip to the B/M. My .4 build is really good but the sucker is hot with a normal drip tip. So another bit of shiny was needed. Much better. Still may need to get some lower nic.

View attachment 339451

youll poke your eye out!!! or worse.... stick it in your nose..

 

[DavidOH]

youll poke your eye out!!! or worse.... stick it in your nose..

I just have to be careful. But it does cool the vape a bit.

 

[Pappy]

I just have to be careful. But it does cool the vape a bit.

Wouldn't it be easier just to make a coil that's not so hot? Obviously, I don't understand the whole sub-ohm thing.

 

[retic1959]

Wouldn't it be easier just to make a coil that's not so hot? Obviously, I don't understand the whole sub-ohm thing.

I'm starting to understand going subohm on an RDA , the chambers a lot bigger than a kayfuns and the airflow is coming from a different direction too . I had to go lower resistance to recover the same amount of flavor and vapor as my 3.1's , I'm running a .8 in the IGO right now and can go to .7 on the SVD and still be under the amp limit , I'm not chasing clouds Pappy , I'm chasing maximum flavor out of it , I'm gonna go lower resistance on the mech and see where that puts it . It's definitely an entirely different animal from the 3.1's .

 

[DavidOH]

Wouldn't it be easier just to make a coil that's not so hot? Obviously, I don't understand the whole sub-ohm thing.

Might be but I like playing around with the coil or coils just to see what I can get from it.

 

[Bronze]

Might be but I like playing around with the coil or coils just to see what I can get from it.

Yes, for many, this is much a hobby as anything else.

 

[hudson_macbeth]

Ok hardware gurus. Question for you. I need to find a mod, vv/vw, that has stainless threads, that will last a a good while, and it has to be inexpensive. My mvp is taking a dump on me, and funds are short, what with the insane amounts veterinarians charge to look at and splint a broken dog's leg. So to get the most bang (or vape if you will) the buck, could i get some suggestions on what I should be looking at please?

 

[Bronze]

Ok hardware gurus. Question for you. I need to find a mod, vv/vw, that has stainless threads, that will last a a good while, and it has to be inexpensive. My mvp is taking a dump on me, and funds are short, what with the insane amounts veterinarians charge to look at and splint a broken dog's leg. So to get the most bang (or vape if you will) the buck, could i get some suggestions on what I should be looking at please?

Inexpensive? I've owned three "inexpensive" regulated mods..two had VV/VW. A VAMO and I currently own an SVD. The VAMO worked fine for me. Liked it plenty good. Then got an SVD and I also like it. I would say it's built a little better than the VAMO. featurewise it's close. Only negative with the SVD is it's tall. REAL tall! If you're a lummox, I would go with the SVD...it has a little more durability. If you are sensitive to size, then you might want to consider the VAMO.

 

[hudson_macbeth]

Do both of those have stainless 510 threads?

 

[Bronze]

Do both of those have stainless 510 threads?

I'm pretty sure they both do but don't hold me to it. Double check when you research them.

 

[hudson_macbeth]

Ok bronze. Thank you very much!

 

[retic1959]

Ok hardware gurus. Question for you. I need to find a mod, vv/vw, that has stainless threads, that will last a a good while, and it has to be inexpensive. My mvp is taking a dump on me, and funds are short, what with the insane amounts veterinarians charge to look at and splint a broken dog's leg. So to get the most bang (or vape if you will) the buck, could i get some suggestions on what I should be looking at please?

I second the SVD , it has stainless steel threads and a spring loaded center pin , tough mod , it packs more of a punch than your MVP 15 watts instead of 11 . It's also capable of firing subohm down to .7 ohms if you want to slap an RDA on it , best bang for the buck is ordering from Fasttech for just under $38 and using US-epacket for free shipping , should take a week and a half to get it if you order while there's no chinese holidays . I noticed Angelecig had them listed but last time I looked they were out of them .

 

[retic1959]

Do both of those have stainless 510 threads?

The Vamo has plated brass , weak threads are still an issue with them , if you order a Vamo get a stainless steel 510 adapter to protect your threads .