Let's Talk Hardware

[Bronze]

I thought that 25 mm was kind of dopey too. But that transition ring does make it a little better.

 

[Dusty_D]

/start rant

If I had any hair on the top of my head, I'd be pulling it out by now.. trying to build these Orchids.

The post screws must be super sharp, because they keep cutting my 28g wire as I tighten them. If I don't tighten them enough, the wire moves and readings are off. 26g works better but then I'd end up with super low ohm coils when built in a dual setup.

Grrr!

/end rant.

 

[Bronze]

/start rant

If I had any hair on the top of my head, I'd be pulling it out by now.. trying to build these Orchids.

The post screws must be super sharp, because they keep cutting my 28g wire as I tighten them. If I don't tighten them enough, the wire moves and readings are off. 26g works better but then I'd end up with super low ohm coils when built in a dual setup.

Grrr!

/end rant.

Is it the hole connections or wrap-around-the screw connection?

 

[Dusty_D]

Is it the hole connections or wrap-around-the screw connection?

Hole connections..

Hmm.. I wonder if I could get it to hold the wire wrapped around the screw.

 

[Dusty_D]

Nope, heads are too small. Pushes the wire out as tightening.

Good idea though

 

[Bronze]

Nope, heads are too small. Pushes the wire out as tightening.

Good idea though

Try filing down the end of the screw?

 

[Bunnykiller]

maybe a washer under the screw head or 10 ga.

 

[Dusty_D]

It's 4 posts, so the screws are tiny and close to each other. The easiest way to do it would be to use the holes. Filing down the bottom of the screws would be the cleaner option.

No energy to futz around with it now.. Another day, another time..

 

[Bronze]

Good luck.

 

[Bunnykiller]

It's 4 posts, so the screws are tiny and close to each other. The easiest way to do it would be to use the holes. Filing down the bottom of the screws would be the cleaner option.

No energy to futz around with it now.. Another day, another time..

hemostats and a knife sharpening stone.......

 

[DavidOH]

 

[rdsok]

Merry Christmas and a Happy New Year to everyone...


Happy Holidays for those that don't celebrate Christmas

 

[Bronze]

Merry Christmas and a Happy New Year to everyone...


Happy Holidays for those that don't celebrate Christmas

Back at yuh RD!!!

 

[Dusty_D]

I got one of them done. Dual coil. .8 ohm. 28g. Clear M-tank and Top fill cap. Phew!!

Loaded with 100% VG Dragons Fire at 3mg.

I tried lung hitting it, and coughed my head off. Not yet recovered from the cold enough to do it yet.

Atleast the damn build is done!! Needlenose pliers and microfile to take the edge off the post screws.

 

[Bunnykiller]

I got one of them done. Dual coil. .8 ohm. 28g. Clear M-Tank and Top fill cap. Phew!!

Loaded with 100% VG Dragons Fire at 3mg.

I tried lung hitting it, and coughed my head off. Not yet recovered from the cold enough to do it yet.

Atleast the damn build is done!! Needlenose pliers and microfile to take the edge off the post screws.

close enuf to hemostats and a sharpening stone

 

[Sirius]

/start rant

If I had any hair on the top of my head, I'd be pulling it out by now.. trying to build these Orchids.

The post screws must be super sharp, because they keep cutting my 28g wire as I tighten them. If I don't tighten them enough, the wire moves and readings are off. 26g works better but then I'd end up with super low ohm coils when built in a dual setup.

Grrr!

/end rant.

I have that same problem Dusty..Makes me have to rebuild three or four times.
Once ya get it going though..awesome vape!

 

[Sirius]

Merry Christmas and a Happy New Year to everyone...


Happy Holidays for those that don't celebrate Christmas

Merry Christmas RD.

 

[icepoet]

Merry Christmas y'all

 

[Robino1]

Merry Christmas Ice!!!!!!!!!!!!!!!

 

[Bronze]

You to Ice!!!