Looking for a new RTA suggestion

[ej1024]

Some one had to make an RTA with a big deck.
Every one makes a 6ml tank with a 17mm deck. That's boring...I have a few.
I needed something I could fit fused 24 in.
Even if the thing held 6ml, I'd still need 8 bottles of juice with me everywhere I go.
I'm a coil builder first and a DIY juice man second so naturally I'm going to feel that way.

If people want more capacity and a little deck, theres a plethora of options for them.

The bv3plus has 18mm deck
If you want bigger than that
Check out the
CALYPSO RTA
MODFATHER
ETCCCC


VAPE ON[emoji36]

 

[whiteowl84]

I can't do a 30mm tank...maybe at home but all my mods are pocket friendly.
I'd just look ridiculous carying that big of a box and tank around.
That's why I'm starting to really like gennys. Small package with big coils.
25mm tanks are where it's at for me.

I'm probably going to dive into the world of mech mods and 25mm RDAs if I could get all this ribbon to stay lined up while I clapton it!!

 

[ej1024]

I can't do a 30mm tank...maybe at home but all my mods are pocket friendly.
I'd just look ridiculous carying that big of a box and tank around.
That's why I'm starting to really like gennys. Small package with big coils.
25mm tanks are where it's at for me.

I'm probably going to dive into the world of mech mods and 25mm RDAs if I could get all this ribbon to stay lined up while I clapton it!!

It's not really that big to carry around bro...


VAPE ON[emoji36]

 

[whiteowl84]

The box or the tank? I realize that a 30mm tank isn't thaaaat much bigger but the mods are. Not just thicker but usually taller and wider too...can you suggest a mod that will take a 30mm with no over hang? I'd really appreciate it.
IIRC most 3 battery diamond shaped (rx200) will still let the tank hang over.
I'd probably use that sort of tank on a mech.

 

[ej1024]

The box or the tank? I realize that a 30mm tank isn't thaaaat much bigger but the mods are. Not just thicker but usually taller and wider too...can you suggest a mod that will take a 30mm with no over hang? I'd really appreciate it.
IIRC most 3 battery diamond shaped (rx200) will still let the tank hang over.
I'd probably use that sort of tank on a mech.

I use my panzer mod for the calypso RTA
It's perfect...


VAPE ON[emoji36]

 

[jersey_emt]

with spaced coils yeah but seems to even out more with touching wraps

this glowed up quite well for the length and have run 2 tank fulls today

flavour n vapour volume have been spot on

I brew my own juice and takes a couple of weeks to start gunging up these sort of coils, but when it does its full length

I decided to give it a shot in my Goon RDA, which offers the easiest way to mount very wide coils because of the clamp system which is similar to your Azeroth RTA. I've settled on 3.5 mm diameter coils on my Goon, so I had a few less wraps than your build -- 22 wraps of 24 gauge SS316L. The dual coil measured at 0.55 Ω. I'm vaping it at 90 watts, the same as you are with your build.

Then I mixed up a small batch of juice that would gunk things up quickly. After going through 10 mL of that, the centermost 8 wraps were fully caked in gunk. The next four wraps (two on each side of the 8 centermost wraps).were gunked but not completely caked over. The next three wraps on either side were discolored but had not started to collect any gunk. The outer wraps still had some sheen to them, with the outermost two wraps on each side looked brand new.

I'm going to try again with one of my juice recipes which keeps coils remarkably clean -- I can go through 15 mL of it and the coils are still shiny, and it takes about 40 mL before it starts to gunk up the coil -- and see how it does with that.