My free labor is worthless... usually worse.
The cost is usually:
my labor (free) + cost to fix what I messed up (expensive)
Cool work though!!
- Status
My free labor is worthless... usually worse.
The cost is usually:
my labor (free) + cost to fix what I messed up (expensive)
Cool work though!!
My free labor is worthless... usually worse.
The cost is usually:
my labor (free) + cost to fix what I messed up (expensive)
Be there done that....have the scars. lol
This is a very cool little vapin' machine (not because I made it). Very concealable and the battery lasts a couple of hours. Throw an extra battery and a few cartos and you're good to go. It's just too labor intensive to make any to sell. With a bit of practice anyone can make one...just get a few extra boxes from madvapes. If you can make a box mod, you can make one of these. Remember, you can always take more off; just can't add if you cut too short. The smallest one I've made was an "oops". I just did some voodoo to make it work.
Damm Para, I would be scared to inhale too hard fearing I would inhale the whole PV.. LOL
Have you ever thought of getting into the micro surgery field?
Have you ever thought of getting into the micro surgery field?
Parallex2, that's a very cool mod. Nice.
Totally ticks me off. I can't even see the cut line where you glued the box together. Sanded and painted well too. lol.
EDIT: Hey..... The same technique could be used to put more head room in a 2xAA box... So my next box mod could be a 14500 5v 2xAA+ rather than 3xAA. Thanks dude! What's the best way to even off the 2 cuts and mate them? Sanding on a flat surface I suppose. Do you reinforce the joint?
Totally ticks me off. I can't even see the cut line where you glued the box together. Sanded and painted well too. lol.
EDIT: Hey..... The same technique could be used to put more head room in a 2xAA box... So my next box mod could be a 14500 5v 2xAA+ rather than 3xAA. Thanks dude! What's the best way to even off the 2 cuts and mate them? Sanding on a flat surface I suppose. Do you reinforce the joint?
Last edited:
OT...
Oh man... every time I see that sig, the song gets stuck in my head ALL DAY....
Oh man... every time I see that sig, the song gets stuck in my head ALL DAY....
Made a few more today....including the Micro Mini Mod. W/O the carto the length is 38mm. I cut the box too short but was able to mod it anyway. I can't make one smaller than this; that's my limit.
OMG, you are absolutely killing me!
is that a rechargeable battery, or a throw away? seems like that would be a good size bat to use in the mini-pill container mod as well....
It's a 14250 like this one at Madvapes.....comparable in mah to a 10440; both will vape for a couple of hours. The one I use is unprotected so it's a couple of mm shorter. Since I don't stack them, it doesn't matter to me whether they are protected or not
Last edited:
You really should make you one; they are a blast. I've got a lot of PV's, but none are as much fun as these.
My son worked on Rango (opens tomorrow) so I'm loading up a few clearomizers, grabbing a couple of batteries, and sticking a Mini Movie Mod in my pocket. Popcorn, Diet Coke, Movie, and Stealth Vaping.....life is good. !
So awesomely amazing! I admire your work Parallex2
Thanks for the kind words; I really appreciate that.
Parallex2 - do you spray paint your finished boxes? If so, what paint do you use? I tried a while ago with some metallic paint and it would never dry properly and just remained sticky... in the end I had to scrape it all off again.
Krylon Fusion is an excellent paint for plastic. Prep the surface, paint, and then let it fully cure. I finish it off with a Polyurethene top coat for added durability.
- Status
Similar threads
