Status
Not open for further replies.

Uncle Ralphie

Ultra Member
ECF Veteran
Verified Member
Aug 21, 2013
1,835
14,909
81
N. E Connecticut
They've arrived. My precious juice babes have arrived.
Right now I just took them out of the package and put them up on a shelf,
later after they've thawed I'll take their little tops off and get air to them.
Mail lady did have them up front with her, but she had to help regular sub
mail guy cuz he didn't have heat in his car and his feet got cold. :blink:
My orange dream bar juice got a little squished. And it's not the fault
of the weather or the mail lady, it would be the fault of whoever packaged
it. I will wait and see it doesn't look though like it's damaged. Will
check it out later and if it is damaged I know MBV would make it right.

band.gifband.gifband.gif

Yaaaay, glad to see your order arrived unscathed. Orange Dream Bar takes awhile to steep anyway, so it should be ok
 

poetic_injustices

Senior Member
ECF Veteran
Dec 11, 2013
276
2,212
Pittsburgh, PA
you mean like probationary boyfriend??:p


I wish. It's been kinda probationary for awhile now. We've been together a long time but I'm starting to question whether or not we are the best people for each other. We are so completely opposite. He's black and white, I live in the gray. My heart is out on my sleeve. His is tucked away somewhere guarded by some serious childhood trauma. Almost 6 years we've been together and we're just not the couple I believed we could be.
 

Ozwald

Vaping Master
ECF Veteran
Verified Member
Nov 12, 2013
5,303
20,368
Montana
As long as it took me to catch up from this morning, that was nothing compared to hauling in a month+ worth of groceries one handed... and I don't need all that much stuff!! I'm pooped!

You can wrap them really tight when they're on the allen key (and you should, they work better that way, especially with 28g) but when you go to put it on your Reo, make sure there's the right amount of tension on the coil as you connect it to the posts - it sounds like that's why sometimes it's bowing and sometimes not.

If you can't torch it while it's on the jig, you could always pre-torch it before you wrap the coil (just use a pair of needlenose pliers)... that'll take some of the springiness out of it for you and make it more likely to stay where you put it.

I forget why I clicked on this one, except for the fact that miss Mia was having troubles :(

I get perfect looking coils every time - I flame the wire twice before I wrap it (but that's because I use twisted wire - once fresh off the roll & once more after I get it twisted up). Then I wrap it really tight around my drill bit, carefully slide the bit out, torch it again, carefully pinch it with some needle nose pliers & put the drill bit back in. Mount with bit in place, remove bit, check resistance & fire it a few times. Wick it & prime the wick. Sounds a lot harder than what it is.

You want me to leave?! Sniff..

Ok, sniff.. I'm leaving now.. :(

No Dusty, don't leave! :cry:

Oh... you didn't. :) Is that a new watch? It looks mighty sharp. :D
 

Sambuca

Ultra Member
ECF Veteran
Jul 23, 2013
2,947
20,505
Albuquerque
As long as it took me to catch up from this morning, that was nothing compared to hauling in a month+ worth of groceries one handed... and I don't need all that much stuff!! I'm pooped!

I forget why I clicked on this one, except for the fact that miss Mia was having troubles :(

I get perfect looking coils every time - I flame the wire twice before I wrap it (but that's because I use twisted wire - once fresh off the roll & once more after I get it twisted up). Then I wrap it really tight around my drill bit, carefully slide the bit out, torch it again, carefully pinch it with some needle nose pliers & put the drill bit back in. Mount with bit in place, remove bit, check resistance & fire it a few times. Wick it & prime the wick. Sounds a lot harder than what it is.

No Dusty, don't leave! :cry:

Oh... you didn't. :) Is that a new watch? It looks mighty sharp. :D

well then, why not sit a spell, eh?
 
Status
Not open for further replies.

Users who are viewing this thread