NEW avs3 (UFS)

[shamreez]

I checked all the four holes mate..
If i inserrt a needle from these holes I can see it from the atty connector.

My draw is getting stuck when I put on the mouth piece..

Will have to do a little more research on it........

 

[Caddyman]

ok good (well not good but at least you ruled that out, also means you probably have a good ufs)

if you just screw the atty onto that connector while everything is taken apart can you pull through the atty?

 

[shamreez]

I tried pulling through the atty at every stage and I can do it till I put on the mouth piece..

Would do a fresh try tomorrow once more and see if the mouth piece is posing the problem or not

Would also try with a fresh batch of atties...

 

[Wylie]

Not to pile on (just trying to help) but I read your post and decided I should put my new UFS together-- the one that was waiting for its SS GGTS.

What the heck? I had the same symptoms. I tried what Poppa D said (poke a needle through the air holes under the CR) and it pushed some black stuff out. I cleaned it up and it's working like a charm now.

I know you said you checked it, but did you put a needle in there?

 

[shamreez]

Hi,

As you can see in the above picture. The holes are open I can insert a syringe from one end of the
bottom hole and it comes out through the other. (For all the holes)

But if you see the second picture I am not able to get a draw once I assemble to his point itself

(Just the base part along with the atty connector and tank bottom)

So I guess I got a faulty part.

I think I would have to wait for imeo to sort this

Cheers guys..

Hope you all got a good one

 

[imeothanasis]

hi sham. I see that the 4 holes in a row on the CT tank are open. Also the 4 holes where you put syrigne are open too. You can also take air without the mouthpiece. That means that mouthpiece is blocked? Please check it

ps..... Can you vape normal without mouthpiece?

 

[VPDownunder]

View attachment 35762View attachment 35763

Hi,

As you can see in the above picture. The holes are open I can insert a syringe from one end of the
bottom hole and it comes out through the other. (For all the holes)

But if you see the second picture I am not able to get a draw once I assemble to his point itself

(Just the base part along with the atty connector and tank bottom)

So I guess I got a faulty part.

I think I would have to wait for imeo to sort this

Cheers guys..

Hope you all got a good one

It may be a silly question but have you opened the air control ring, it looks closed in that second pic is all.

 

[shamreez]

Hi,

I checked the mouth piece and it is fine. I cannot get a draw with just the atty connector, base ring and tank base connected.

@VPDownunder : I tried drawing with holes open and also close the pic was when I was trying with the holes closed.


Also I can get the draw properly when the Atty connector pin is removed from the base. But once it is removed I cannot get a draw

 

[imeothanasis]

so, air holes are open, and mouthpiece is open too. And you cant take air with or without mouthpiece?

 

[shamreez]

No I cannot take air even without assembling the complete UFS

The draw is blocked with just the atty conn, base ring and tank base

 

[shamreez]

I had posted the doubt to a member in a different forum and he suggested that the pin might be blocking the hole in the base of the atty.

This does sound possible coz I am able to take a draw when the pin is not inserted.

If this is the case any of you know any work around where I can get it vaping

 

[shamreez]

Next time any of you see me please ensure that you wack me in the head real hard..

Every one told just one thing from the begining,..

To clean the air holes and it was not... (I was more concerned about the air holes in the bottom of the atty that I did not care much about the 4 air holes I had blowed in to them but did not use the needle in it)

I just did it and Immediately I saw the reason of my trouble the black stuff which has been mentioned before by lots of people..

It is now vaping real good (Need to get some LR atties though as the normal ones are not producing that good vapour

Sorry everyone for making you think there was something wrong with the UFS

The problem was only with me

And thanks to all for the support..

And a special apology to you imeo to make you think of this because of my stupidness during your holidays........

 

[inquisitorj]

It would be really helpful if there was an ecig wiki for the UFS. I don't know who setup the ones that are there for the GGTS and AVS, but those are great!

 

[Daz 7401]

Glad you got it fixed Shamreez. Daz

 

[Poppa D]

Lube those rubbers.

 

[shamreez]

ooh yeah...

planning a proper clean of my baby this weekend..,

Would buy some nice polish also to keep it shiny
I like the terms we use...

put a needle in the holes to clean them...
Lube those rubbers...

 

[inquisitorj]

CRAP! I think I lost an o ring from my center pin. It wiggles now and leaks juice. How many o rings are there in the center pin part and where do they go? I have 1 tiny one that is tight on the pin and one that is larger that is at the base. I will see if I can post a picture.

 

[shamreez]

CRAP! I think I lost an o ring from my center pin. It wiggles now and leaks juice. How many o rings are there in the center pin part and where do they go? I have 1 tiny one that is tight on the pin and one that is larger that is at the base. I will see if I can post a picture.

I had three..
One big one and two real tiny ones...

God help u if you lost that tiny one coz finding it when it was right in front of me was a task........

It is in one of the image i had posted in the thread in the last page

 

[inquisitorj]

here is what I have now.

The 2 with the red arrows are what I have. Are they in the right place? Where would the 3rd o ring go?

 

[Thierry-P]

Their must be 2 little o-rings together (2mm x 1mm), when you screw the hexagonal nut they come into the plastic piece and make the sealing. Verify that the 2d is not in the plastic piece. The 3rd o-ring (the bigger) is in the right place, you take it off if the connector pin don't make contact with your atty.