New Genesis type atomizer by DID!

[Jim Damianidis]

hI
OD 20mm
ID 18mm
The DCT tanks fit on him cutting the High of the olastic tube!
If the DCT tube is a litle big you must find thicker o-rings and thats it!

 

[gtbb]

Day 8 in ISC New York. Time to run a trace I do believe.

 

[N rustica]

hang in there, gtbb, i ordered mine 5/25 and it arrived today. i live a hundred miles from the jfk airport.

 

[NC_Fog]

Here you go folks...

Marty

 

[fuzzione]

Wish I could give you 2 likes for that one NC. Good job.

Please share details of the tube. Material, where sourced, any useful construction tips/suggestions, stock o-rings ok? etc.

 

[johnsnhu]

Looking good NC!

Sent from my Galaxy Nexus using David Copperfield's magic fairy dust.

 

[denali_41]

Wish I could give you 2 likes for that one NC. Good job. Please share details of the tube. Material, where sourced, any useful construction tips/suggestions, stock o-rings ok? etc.

all that plus what tool did you use to cut the tube with??

 

[NC_Fog]

Wish I could give you 2 likes for that one NC. Good job.

Please share details of the tube. Material, where sourced, any useful construction tips/suggestions, stock o-rings ok? etc.

I used a dct tank cut down to the height of the ss DID cylinder. I did this with a Rigid #10 tubing cutter with a cutting wheel for plastic tubing(special ordered the cutter wheels years ago). I then lightly filed(rat-tail file, rasping/circular motion) each end of the clearo leaving a very slight taper so the DID ends could be inserted into it without damaging the o-rings. I lubed the o-rings with a couple of drops of juice to prevent binding and possibly damaging the threads on the center tube.

Marty

 

[johnsnhu]

I used a dct tank cut down to the height of the ss DID cylinder. I did this with a Rigid #10 tubing cutter with a cutting wheel for plastic tubing(special ordered the cutter wheels years ago). I then lightly filed(rat-tail file, rasping/circular motion) each end of the clearo leaving a very slight taper so the DID ends could be inserted into it without damaging the o-rings. I lubed the o-rings with a couple of drops of juice to prevent binding and possibly damaging the threads on the center tube.

Marty

Nicely Done!

Sent from my Galaxy Nexus using David Copperfield's magic fairy dust.

 

[fuzzione]

Great idea. I'm tempted to order some fused quartz tubing for this application.

 

[RRoberts]

That deserves another look! Great job Fog!

Here you go folks...

Marty

 

[motomatt]

Here you go folks...

Marty

That is way sweet , How much would you charge to make me 2 ?

 

[denali_41]

Well..my DID went from NYC customs to a notice being left in P.O. box in Alaska,,in a record time of just under 2 hours

 

[motomatt]

How do you adjust the OHM's on the Genesis ?
If I am using 100% vg what size of mes is best to use 325 or 400 ss mesh ?
Thanks for any help.

 

[aziffel]

How do you adjust the OHM's on the Genesis ?

More Wraps around the wick=higher ohms,or thinner wire,same #wraps=higher ohms

 

[motomatt]

More Wraps around the wick=higher ohms,or thinner wire,same #wraps=higher ohms

Thank you

 

[fuzzione]

This chart might also help
see post #820

http://www.e-cigarette-forum.com/forum/atomizer-mods/197617-bulli-a2-t-82.html#post4361672

You can enter your target ohm in the upper left box and it does the calculations.

 

[NC_Fog]

motomatt, you can cut it with no problem. Just go for it...lol. I just cut a spare one(my last one...lol) with a regular pair of tubing cutters(metal) to see how it would do. It did take longer and I had to use more pressure but it cut the tubing just fine. I bet it can be done with a fine toothed hacksaw using only the back stroke(pulling). A Dremel with the right wheel would probably be excellent.

Marty

 

[N rustica]

I used an electric stove element to condition the wick and did the 3X burn with pure VG. After wrapping, it took only about 20 minutes to get it vaping like a train. I'm now considering using a lower mg. nic because I'm getting dizzy.

Thank you to Paul for making this.

 

[motomatt]

This chart might also help
see post #820

http://www.e-cigarette-forum.com/forum/atomizer-mods/197617-bulli-a2-t-82.html#post4361672

You can enter your target ohm in the upper left box and it does the calculations.

fuzzione you are what got me in to the Genesis, Thank you