New Genesis type atomizer by DID!

[motomatt]

motomatt, you can cut it with no problem. Just go for it...lol. I just cut a spare one(my last one...lol) with a regular pair of tubing cutters(metal) to see how it would do. It did take longer and I had to use more pressure but it cut the tubing just fine. I bet it can be done with a fine toothed hacksaw using only the back stroke(pulling). A Dremel with the right wheel would probably be excellent.

Marty

Thank you

I used an electric stove element to condition the wick and did the 3X burn with pure VG. After wrapping, it took only about 20 minutes to get it vaping like a train. I'm now considering using a lower mg. nic because I'm getting dizzy.

Thank you to Paul for making this.

Thank you

 

[Striker911]

Order in processing. Thanks for the updates, its good to know I'm in good capable hands

 

[fuzzione]

fuzzione you are what got me in to the Genesis, Thank you

A pleasure. I'll be asking my share of questions and guidance when mine arrives, believe me. This is my 1st rebuildable.

I'm presently researching fused quartz, cutting tools and carborundum honing stones

 

[gtbb]

Postman was very good to me today! Better than Santa ever did. The pleasure begins. Thanks to e-vape.gr
Amazing how quick they could ship to the USA and be held by our USPS.

 

[dspin]

The DID on a GGTS, GGTB, and a Precise P-18 - fits TB and P-18 like it was made for them

 

[fuzzione]

The DID on a GGTS, GGTB, and a Precise P-18 - fits TB and P-18 like it was made for them

Absolutely stunning dspin. I am truly envious. Great photo skills too.

 

[Karla Lyle]

Just went to the website and it says out of stock. Any idea when they might be back in stock. Also what is the price on them? I just got my first Genesis style a few days ago and I din't think I will ever buy another premanufactured atty again. I am just looking for other alternatives and someone recommended your DID. Looks great. Also what is the shipping cost and time? Thanks

 

[Striker911]

Just went to the website and it says out of stock. Any idea when they might be back in stock. Also what is the price on them? I just got my first Genesis style a few days ago and I din't think I will ever buy another premanufactured atty again. I am just looking for other alternatives and someone recommended your DID. Looks great. Also what is the shipping cost and time? Thanks

Hey Karla. Its on pre order. Put in your cart and pay. Wont take long to get yours. It cost $102 and some change. Shipping is certified and its free.

 

[denali_41]

Well..my DID went from NYC customs to a notice being left in P.O. box in Alaska,,in a record time of just under 2 hours

got it in my hand now,,maybe i will have time tonight to assemble it ?? am i going to need to do any soldering ??

 

[NC_Fog]

No soldering, but you will need to heat the ss wick red hot to oxidize it(3 times recommended).

Marty

 

[Huffelpuff]

First page or on website watch the video Jim made. It's very easy to put together.

 

[KickServe]

Mine are in Denver PO. Should get it tomorrow. Have been meeting the postman by the mail box for the last couple of days

 

[KickServe]

I usually vape mostly VG juices - full or 80 or 70 vg - and I have a good bit of 325 mesh in stock. Today I got a big order that accidentally got reversed in the PG/VG ratio and ended up with 70PG juice. Does the 325 mesh work with that or should I be using 400? Any one with any experience in this area ?

 

[johnsnhu]

I usually vape mostly VG juices - full or 80 or 70 vg - and I have a good bit of 325 mesh in stock. Today I got a big order that accidentally got reversed in the PG/VG ratio and ended up with 70PG juice. Does the 325 mesh work with that or should I be using 400? Any one with any experience in this area ?

I would assume more mesh(400) for thinner PG based juice... but what do I know...

Sent from my Galaxy Nexus using David Copperfield's magic fairy dust.

 

[Striker911]

Try it and see. Mac taught me to pinch the end of the mesh and it wont poor out of the end. Should help if the juice is too thin.

 

[NC_Fog]

OK folks the clear tank is doing great with no leaks at all(stock O-rings). I appreciate all of the comments and likes you all have made. I can't take all the credit for this, it was Jim's suggestion that the dct tanks would work. All I did was the hands on part.

I have a question for all of you more experienced at the rebuildables. I seem to struggle some getting the coil on without hotspots or just outright popping. I heat/dunk the wick as suggested then burn off juice a couple of times but to no avail. Seems it take me 3 or 4 times each time for success. Then when I am, this thing is unbelievable. I'm only putting 3 rounds on to achieve a 1.8 to 2.2 ohms reading.

Enjoy The Journey...

Thanks in advance,

Marty


ETA...I think I was wrapping the wick to tight. Not sure but re-wrapped it somewhat loose and all is well. Suggestions appreciated.

 

[dspin]

I usually vape mostly VG juices - full or 80 or 70 vg - and I have a good bit of 325 mesh in stock. Today I got a big order that accidentally got reversed in the PG/VG ratio and ended up with 70PG juice. Does the 325 mesh work with that or should I be using 400? Any one with any experience in this area ?

I use 325 for all vg, 70 % vg. 400 for 70 pg. No worries you can use 325 for 70 pg - you will tell the diff. DID should have come w/both 325 and 400 mesh.

OK folks the clear tank is doing great with no leaks at all(stock O-rings). I appreciate all of the comments and likes you all have made. I can't take all the credit for this, it was Jim's suggestion that the dct tanks would work. All I did was the hands on part.

I have a question for all of you more experienced at the rebuildables. I seem to struggle some getting the coil on without hotspots or just outright popping. I heat/dunk the wick as suggested then burn off juice a couple of times but to no avail. Seems it take me 3 or 4 times each time for success. Then when I am, this thing is unbelievable. I'm only putting 3 rounds on to achieve a 1.8 to 2.2 ohms reading.

Enjoy The Journey...

Thanks in advance,

Marty


ETA...I think I was wrapping the wick to tight. Not sure but re-wrapped it somewhat loose and all is well. Suggestions appreciated.

Thats the key, solid connections and not wrap the wick too tight or too loose. Heat your wire before wrapping, will make it easier.

 

[denali_41]

its official,,,the mesh is smarter then me !! watched jims video but most of the mesh wrapping is out of the view,,,
first mesh was too dang thick,,so i cut some off then it was too skinny ,,aarghhhhhhhh
got frustrated and gave up on the second attempt and posted this
i obviously need some help ..
what should the size of the mesh be ?? inches please
is there a better vid for making the mesh wick ??

 

[Striker911]

its official,,,the mesh is smarter then me !! watched jims video but most of the mesh wrapping is out of the view,,,
first mesh was too dang thick,,so i cut some off then it was too skinny ,,aarghhhhhhhh
got frustrated and gave up on the second attempt and posted this
i obviously need some help ..
what should the size of the mesh be ?? inches please
is there a better vid for making the mesh wick ??

When the wick was too thick you couldn't just keep twisting it, like rolling an analog yourself to make it thinner and a tad smaller? I would think that at least one end of the mesh that comes with it would be the correct size and you just have to twist it up to make it fit. Then cut the tube to size once you put it in the tank. Hope this helps.

 

[denali_41]

When the wick was too thick you couldn't just keep twisting it, like rolling an analog yourself to make it thinner and a tad smaller? I would think that at least one end of the mesh that comes with it would be the correct size and you just have to twist it up to make it fit. Then cut the tube to size once you put it in the tank. Hope this helps.

when i smoked i couldn't even roll a decent ciggy,,not even when i would partake of the funny stuff either :O what should the size of the mesh be to start with ??