New Genesis type atomizer by DID!

[Scottinboca]

These are the ones. They fit perfectly, but are all sold out from this vendor.
4.5ml "Shorty" Cartomizer Tank by SmokTech

 

[Scottinboca]

Here they are in your part of the world.
EcigModShop Australia - SmokTech Dual-Coil 4.5ml 2.5 ohm Tank Kit (Aluminium-DCT)

I have two broken first break was my fault I dropped it! just a crack but stuffed all the same. Second one was all good yesterday just loved that Lime, this morning I wake up get coffee then I notice juice all over table a big chunk of pyrex had popped out Why Why!, any idea's? maybe I screwed top on too tight. Anyway back to the stainless I like my lime too much.
Would be nice to find a juice friendly plastic.
Best of luck with ordering folks.

 

[burnie71]

You can use the 4.5ml smoketech DCT tanks. They fit perfectly and can handle all juices.

Thanks mate, must get hold of some I like to see the juice.

 

[kwalka]

I have two broken first break was my fault I dropped it! just a crack but stuffed all the same. Second one was all good yesterday just loved that Lime, this morning I wake up get coffee then I notice Juice all over table a big chunk of pyrex had popped out Why Why!, any idea's? maybe I screwed top on too tight. Anyway back to the stainless I like my lime too much.
Would be nice to find a juice friendly plastic.
Best of luck with ordering folks.

Tanks that crack do so because they don't have room to expand.

 

[BennyB]

Anyone know of a clear tank that would fit the temon atomizer? It's 16 mm.

 

[Scottinboca]

You can check here, I'm not sure if they have what your looking for.
https://www.ibtanked.com/custom-cut-tubes/16mm-20mm

Anyone know of a clear tank that would fit the temon atomizer? It's 16 mm.

 

[Scottinboca]

They do. They have tanks for both regular and short DID.
https://www.ibtanked.com/custom-cut-tubes/common-sizes

Anyone know of a clear tank that would fit the temon atomizer? It's 16 mm.

 

[burnie71]

Tanks that crack do so because they don't have room to expand.

Thanks, I assume then I have over tightend

 

[Scottinboca]

That's one reason I like that plastic, it's very flexible and not ridged at all.

Thanks, I assume then I have over tightend

 

[BennyB]

So excited for my Temon! I love the look of the polished stainless steel and brass connector/button. Thanks Jim!

 

[classwife]

I just broke my pyrex from my short DID trying take a foto

I seem to have missed a lot lately !

Wow !

 

[B2L]

Whats with all the new toys a week before the big show? Anybody feel free to get 2 of these and just PM me for my address. I have been very good this year, I swear. You can ask my mom... Umm ok dont ask my mom, but I swear I've been good.

My DID with its new 635 mesh wick and lovely 28 AWG Kanthal coil can attest to this.

 

[studiovap]

These are the ones. They fit perfectly, but are all sold out from this vendor.
4.5ml "Shorty" Cartomizer Tank by SmokTech

I have used these and they are great, but I found they are a fraction too long and mood a light sand otherwise you can get a poor ground connection with your Ohms shooting up all over the place die to the center spindle not quite seating firmly in it's threads. Also they don't respond well to heat while dry burning repeatedly while setting up a stubborn wick and coil. Just a couple of reasons to give the Pyrex from Jim some consideration. Also I'm yet to fine the 4.5ml ST tanks without the end caps carto and drip tip, making it as expensive as the Pyrex in most cases.

 

[studiovap]

Hi I am really sorry but the POLDIAC will not be available
till I solve a big disadvantage

I found a bad spot at the DID Stealth Design Button!!

My desk is not so good spirit level (not perfect horizontal)
so I lied the POLDIAC on it and it started running away!
This is bad! Very bad!!
you do not have to pay so much money for something does not worth it!
I do not want this to happen! Never!!
I think I have proofs about that !!! lol
So waht do you think?
Is this a big problem for you ?



ONE MORE..

As others have mentioned Jim, the very best (and hardest to find available I might add) battery mods are rollers in the truest sense of the word, lying a quality mod on it's side on a non padded surface is sac religious anyway, as you are just asking for scratches in the finish.

 

[burnie71]

I have used these and they are great, but I found they are a fraction too long and mood a light sand otherwise you can get a poor ground connection with your Ohms shooting up all over the place die to the center spindle not quite seating firmly in it's threads. Also they don't respond well to heat while dry burning repeatedly while setting up a stubborn wick and coil. Just a couple of reasons to give the Pyrex from Jim some consideration. Also I'm yet to fine the 4.5ml ST tanks without the end caps carto and drip tip, making it as expensive as the Pyrex in most cases.

Yes you are right re cost, but only recieved 2 tubes from Jim last week so its been an expensive exercise so far! guess I will be more gentle next lot.

 

[Pete54]

We're still on for tonight, right??????

 

[NatGasMan]

Yes we are Pete!

 

[Pete54]

Ok. I just didn't want to set my alarm for 2:30am only to find out that they weren't for sale because they ROLL ....

 

[Pete54]

Hopefully Jim will have the 18650 size for sale because it doesn't show that option on the site anymore.

 

[NatGasMan]

Yes, Jim said it was a go even with the roll. I asked about the 18650/18500 kicked tube also and he said it will be available.

Jim, on your site there is not an option on the drop down box for the tube size selection for the 18650/18500 kicked tube. I guess you will fix it in the morning?