New Joyetech 20watt eGrip
- Thread starter Racehorse
- Start date
- th_trl_thread_readers 0
- Status
Mine came in today. So far it's amazing!. Just changed to a slightly longer cotton.
Sent from my iPhone using Tapatalk powered by Evolv DNA30
I'd love to get that drip tip... where'd ya find it?
I got it quite sometime back. It's from Vicious Ant.
Sent from my iPhone using Tapatalk powered by Evolv DNA30
They are nice but pricey!
Well i tried the method of taking the air out first with a needle bottle, works a treat! Zero leakage! And filled the tank right up. Just awesome.
Just helps to have a needle bottle on hand
Anyone know of a good needle bottle i can use for transport? Has to be a good rugged one as i have a normal bottle with a needle on top with a rubber stopper. Can't carry that around with me!
Oh i have a Ucan by innokin but can't remove the air with that one.
This method doesn't work with a normal juice bottle. Has to be a needle end.
Any suggestions?
I've used an empty pill bottle as a container for the needle bottles before. With some organic cotton stuffed in the bottom as a shock absorber, leak absorber and emergency wicking material.
I have to plead ignorant one this one. Care to brief me on what it means to take the air out first?
SD Can might work for you. Kinda like the Ucan, but it has a plastic bottle on the inside and a longer needle tip. The button on the side actually squeezes the bottle inside
Awesome! Where may i buy this from? Thank you!SD Can might work for you. Kinda like the Ucan, but it has a plastic bottle on the inside and a longer needle tip. The button on the side actually squeezes the bottle inside
Ok well basically, my issue is when i fill up from the side door (larger hole), the e liquid comes straight back out the smaller hole. So filling this beast is almost impossible.
So to rectify this i just unscrew the rba base and fill from the bottom.
However as another poster suggested, i can using a needle bottle unpressureize the tank first by squeezing the needle bottle in the smaller fill hole to suck out the air that's causing the liquid to come right back up.
Then go back to the larger fill hole to fill my tank up.
works successfully with no leakage of sort. I hope i am making sense
If not i shall elaborate with some pics if that may help.
Awesome! Where may i buy this from? Thank you!
Ok well basically, my issue is when i fill up from the side door (larger hole), the e liquid comes straight back out the smaller hole. So filling this beast is almost impossible.
So to rectify this i just unscrew the rba base and fill from the bottom.
However as another poster suggested, i can using a needle bottle unpressureize the tank first by squeezing the needle bottle in the smaller fill hole to suck out the air that's causing the liquid to come right back up.
Then go back to the larger fill hole to fill my tank up.
I hope i am making sense
If not i shall elaborate with some pics if that may help.
I'm sorry, But what you are saying makes no sense to me, unless you are trying to fill with a full size nipple that won't go into the large fill hole. If that is the case, I think the problem is the amount of liquid coming out of the bottle and that it probably isn't/wont seal over the hole. If that is the case, the egrip isn't leaking, you're just making a mess!
Most of the smaller bottles I've purchased in the last year have small enough tips to fit well inside the large hole. It is not pressurized. You're not sucking air out of the tank without it rushing right back it.
There may be a skin of liquid covering the small hole, but you can clear that by touching it with the tip of the bottle or squeezing a puff of air at it, wipe the fill compartment out with a paper towel...
Don't make this thing more complicated than it is. Needle bottles are more of a pain to carry than you need, and tend to be really slow to fill. JMHO.
No sure i understand. But for me if it's not a needle tip, i get this issue.I'm sorry, But what you are saying makes no sense to me, unless you are trying to fill with a full size nipple that won't go into the large fill hole. If that is the case, I think the problem is the amount of liquid coming out of the bottle and that it probably isn't/wont seal over the hole. If that is the case, the egrip isn't leaking, you're just making a mess!
Most of the smaller bottles I've purchased in the last year have small enough tips to fit well inside the large hole. It is not pressurized. You're not sucking air out of the tank without it rushing right back it.
There may be a skin of liquid covering the small hole, but you can clear that by touching it with the tip of the bottle or squeezing a puff of air at it, wipe the fill compartment out with a paper towel...
Don't make this thing more complicated than it is. Needle bottles are more of a pain to carry than you need, and tend to be really slow to fill. JMHO.
I've used 5 different bottle styles and they ALL cause major leaking from the smaller hole. It just comes right back up.
Have tried tilting the egrip, squeezing slower. Nothing. Just works with a needle tip which is annoying. But oh well.
I had issues too until I switched to a needle tip. Bought a bunch of them from Ebay, and they work well - and fast (I use high PG). I keep them in a plastic bag in my purse, though, in case they leak
I got mine from Steammonkey.com Might be worth searching around a bit though, maybe cound find someplace closer to the UK.
Hello I got a quick question. What material is used to cover the wooden egrip? I belive it is not a real wood or paint. So when it wears of or gets damaged is there a silver metal surface under there? Is it possible to remove the wooden finish? Im about to buy one and inbetween wooden and silver.
Thanks.
Thanks.
Anyone else finding the seal on top of the rba comes off and gets jammed around the air pipe in the tank? I've lost 3 seals this way. For all the seals that come with the kit, that is the one that needs replacing the most and they don't give you any spares
Do you mean the little metal cap? That's the only thing I've had come off, and I just pull it out with tweezers.
- Status
Similar threads
- Locked
- Locked
