New Youde RTA the Bellus
- Thread starter mecca7979
- Start date
- th_trl_thread_readers 0
- Status
No leaks here either, I was just amazed at the performance and making a lame attempt to be funny.
Bellus is very very good. But mine has been displaced by an Avocado. Which later has been displaced by a Griffin ftw. All excellent in their own ways, all have pros & cons.
tapatyped
Bottom filling will be difficult. You'll need to take the atty off your mod, screw off the securing ring at the bottom, and remove the build deck. The size of the juice holes will pretty require you to use a syringe. That's if I remember correctly. It's been a while since I opened up my Bellus.
Sent from my M7_PLUS using Tapatalk
I fill mine from the bottom only. And without syringe but my bottles do have those skinny syringe like nettle tops. With a regular nipple top bottle it's not too difficult either.
I carry 15ml bottles (have 1 for each flavor that are filled from 100 & 120's) around when packing the Bellus to work and the standard Needle-Tips on those fit perfectly inside the Fill Holes.
You can get them on ebay for @ $6-$7 for 15 of them. Those work with every RTA/RDA I have except the Squape R which definitely requires a Unicorn or Hypo-Needle Tip.
Of course ya can go High-End and get an Innokin U-Can but those run about $17 each. Nice and work great (have 2 of those) but not practical for every Flavor if you have 9-10 in rotation. Guess you could clean and change Flavors in the U-Can but too much work for me
You can get them on ebay for @ $6-$7 for 15 of them. Those work with every RTA/RDA I have except the Squape R which definitely requires a Unicorn or Hypo-Needle Tip.
Of course ya can go High-End and get an Innokin U-Can but those run about $17 each. Nice and work great (have 2 of those) but not practical for every Flavor if you have 9-10 in rotation. Guess you could clean and change Flavors in the U-Can but too much work for me
+1
These tips have fit every RTA that I have.
These tips have fit every RTA that I have.
+1
These tips have fit every RTA that I have.
I just put all my juice in those so I can put any juice I have into any RTA. Top fill, bottom fill, screw to fill, it doesn't matter
. I've been doing it for 2 years so filling is never an issue.
The one plus of using high PG liquid is needle top bottles fill nice and quick so not seeing a problem with bottom filling on the bellus. I'm just going through fasttech frustration at the minute it's on it's way I just don't know when I'll get it but within a week I think. Then I'll have a bellus and a higo (thanks to Roxy's review of it ) to play with and figure out so enough to keep me busy for an hour or two.
) to play with and figure out so enough to keep me busy for an hour or two.
Wow... Strange indeed. I only build my Bellus with Ti so can't help on that.
What Ohms, Wraps, Coil I.D., Mod, Power (Settings)... Give all the details so others can help ya nail down your Gremlin(s).
But I can attest that the Bellus in one of the most flavorful and great Vapor mass RTAs I've ever owned/used.
So you gotta have something major Incorrect.
What Ohms, Wraps, Coil I.D., Mod, Power (Settings)... Give all the details so others can help ya nail down your Gremlin(s).
But I can attest that the Bellus in one of the most flavorful and great Vapor mass RTAs I've ever owned/used.
So you gotta have something major Incorrect.
Last edited:
I think the Bellus is a top notch flavor tank as well. I do prefer my coils up higher so that only the bottom third or so is visible through the air slot.
In one I have 2mm 26/32 Claptons. The other has 2.5mm 26g 316L SS.
In one I have 2mm 26/32 Claptons. The other has 2.5mm 26g 316L SS.
I mostly build single coil
28 or 26awg on 2mm / 6 to 15 wraps 0.60 to 1.3ohm
I am actually still searching the ideal build for me so I change a lot.
I don't have problem with my other tanks at least I know 1 build for each that I know will work.
Aromamizer vertical on 2.5mm
serpent 28awg twisted on 3mm
Bachelor 22awg on 3mm I get the taste but Bellus I still search...
28 or 26awg on 2mm / 6 to 15 wraps 0.60 to 1.3ohm
I am actually still searching the ideal build for me so I change a lot.
I don't have problem with my other tanks at least I know 1 build for each that I know will work.
Aromamizer vertical on 2.5mm
serpent 28awg twisted on 3mm
Bachelor 22awg on 3mm I get the taste but Bellus I still search...
Both tanks arrived today and after a good soak the bellus was built with a single 430 ss .5 ohm coil and using the last of my 60\40 pg\vg and it's giving great flavour and was so easy to work with a truly brilliant tank. I have my wicks going halfway down the juice channels and it's keeping up a very good consistent vape for the money this costs I cannot think of any real fault. There was a slight smell of machine oil but nothing visible it was quite a clean tank and totally blemish free but I'm just in the habit of soaking them lol. As for the higo that's a whole different story and nightmare altogether at this point I'll likely be buying a couple more bellus tanks unless when I do get the higo working well it blows the bellus out of the water I'm not holding my breath on that.
It won't blow the Bellus out of the water. Bellus is top of the heap.
That being said, I hope you get your HIGO sorted out. It's a good flavor tank.
That being said, I hope you get your HIGO sorted out. It's a good flavor tank.
I hope so, too. I just got another Higo from FT and mine is as nice as my first one. Did it have any machine oil? A little. But, not as much as my $200 SquapeR did. For $200 I wasn't expecting something I had to wash 3x
- Status
Similar threads
