New ZMax is here - Variable Wattage/Variable Voltage

Status
Not open for further replies.

Dieseler

ECF Guru
ECF Veteran
Verified Member
Sep 24, 2011
17,341
14,062
Illinois
I just obtained my unit. Oh, boy looks like I have to figure some things out. I looked at the 8th setting but how do I dial in for watts? I suppose I should have been reading about the v-max. I can't read small print...I will have to find my clue finder aka magnifying glass. Darn should have went for a eye exam....LOL

Oh, I didn't have to sign for it.
Lucky you !
Yes what DW said on the watts settings . The screen can be little hard to read at first as RMS looks like at least to me - ANS then again my eyes are bad too !
 

Sdh

ECF Guru
ECF Veteran
Aug 31, 2010
10,509
17,194
U.S.
Lucky you !
Yes what DW said on the watts settings . The screen can be little hard to read at first as RMS looks like at least to me - ANS then again my eyes are bad too !
I know but my ADD is kicking in full force. I set the unit down and will play/discover later. :) Oh, Dies Cheeseburgers sounds so good. I would try a vape. Just to be different. No fish or crab juice tho. :)
 

Dieseler

ECF Guru
ECF Veteran
Verified Member
Sep 24, 2011
17,341
14,062
Illinois
Sd i understand i have a hard time with TV remote ...lol
But im getting this little by little, just i forget whats what sometimes - ok most times and reason why i printed this menu option thing out and keep it on my desk.
Perhaps it can help you as well.

1.Uu = Adjust Voltage up
2.Ud= Adjust voltage down
3.S= Standby (On/Off)
4.Uc= Check voltage of battery
5.Ds= Various displays - Sub menu
Do=Display atomizer/cartomizer output voltage
Du=Display battery output voltage
Dr= Display atomizer/cartomizer resistance
6. Led =On/Off
7. = Voltage power
8. =Change voltage calculation method RMS or mean calculation

In the event of a fault the following codes may appear on your Zmax device.

LOR = ATOMIZER/Cartomizer resistance is to low
LOU= Battery voltage is too low, replace or charge battery
WSC= Short circuit in faulty atomixer /cartomizer
 

Ultra

Unregistered Supplier
ECF Veteran
Feb 19, 2009
947
111
Canada USA
www.electronic-cigz.com
I have posted the full Zmax manual here - Zmax V2 New Manual
.... although, Dieseler's version is a lot easier to read and understand!!! Ty Dieseler :)

1.Uu = Adjust Voltage up
2.Ud= Adjust voltage down
3.S= Standby (On/Off)
4.Uc= Check voltage of battery
5.Ds= Various displays - Sub menu
Do=Display atomizer/cartomizer output voltage
Du=Display battery output voltage
Dr= Display atomizer/cartomizer resistance
6. Led =On/Off
7. = Voltage power
8. =Change voltage calculation method RMS or mean calculation

In the event of a fault the following codes may appear on your Zmax device.

LOR = ATOMIZER/Cartomizer resistance is to low
LOU= Battery voltage is too low, replace or charge battery
WSC= Short circuit in faulty atomixer /cartomizer​
 

Sdh

ECF Guru
ECF Veteran
Aug 31, 2010
10,509
17,194
U.S.
It was misrouted to a different Post office. I have had this happen before. My item from the East Coast went to the West Coast and then finally to WI. Hang in there I believe you should get it soon!

An explanation is in this glossary of terms.....
Just look in the glossary of postal terms as USPS...it is there.

Unable to link here. Sorry.
 
Last edited:

salemgold

ECF Guru
Supporting Member
ECF Veteran
Verified Member
Jul 5, 2010
28,155
63,784
South Carolina

dwcraig1

Vaping Master
ECF Veteran
Verified Member
Mar 17, 2012
9,012
48,917
Imperial Beach, California
I think it really good! However, my only critique would be the end cap. I am using a Panasonic and it fits too snug. I have tried some other batts 18650. It the same...a really tight fit. I have heard it can cause some problems.
I have had four Max's so far (still have 3, sold 1) all the short battery caps had a spring the length of the shorter one in the picture except the v2 that I just got.
It had the same long spring as the extended cap so i switched it with the spring that came in the short cap of my v1.
Then I cut one coil off the extra long spring, heated till red the cut end and just pushed it down flat like the other end. I would cut the one in the extended cap but I use it for both battery setup and it would be to short for the 18650. springs.jpg
5 coils vs 4 coils
 
Last edited:
Status
Not open for further replies.

Users who are viewing this thread