Nuppin'

[Tamer El-Meehy]

I’ve never tried a nuppin, would love to buy one. I saw one sell recently I just didn’t have the cash at the time

For me it's one of the most agile atties I've seen. Suits my vaping range just fine (MTL - RLH).

 

[Spydro]

Should sell some of that older stuff if you don’t use it. I’d love a chalice ii haha

OK we need to talk about those Nuppins of yours [emoji1]

I decided long ago not to deal with the mechanics and hassles of selling or shipping anything on line ever again. So none of my gear is for sale, end of story.

 

[YePsTeR]

I'm the opposite.....I am always looking at the for sale or trade thread. Keep your eyes pealed..lol

 

[Tamer El-Meehy]

I'm the opposite.....I am always looking at the for sale or trade thread. Keep your eyes pealed..lol

Same here..although I've become more selective lately!

I decided long ago not to deal with the mechanics and hassles of selling or shipping anything on line ever again. So none of my gear is for sale, end of story.

Can't blame you for that...all it takes is one bad experience

 

[Vapefiend]

I decided long ago not to deal with the mechanics and hassles of selling or shipping anything on line ever again. So none of my gear is for sale, end of story.

I respect that.

 

[kas122461]

Personally I have never sold anything that I have purchased for vaping, I am still not convinced, that vaping products are going to be available in the future as we now know it. I would rather have all this old stuff around to fall back on if I need to, the old better safe than sorry thing.

KAS

 

[puffon]

Hey Nuppin fans!
I bought a V2 in the classies a couple years ago.
It was missing a side grub screw.
After talking to Peter, I think he said I needed a M2 x 2.5mm screw.
Finally ordered some from FT.
Went to try them...no go?
They look to be the same size, but the threading on the FT ones are coarser.
The originals seem to have a fine thread.?
Are there different threadings, or a FT screw up?
What size do I need? and where to get them?
Thanks!

 

[Train2]

Probably a Fasttech quality thing - that's the right size... Here is a direct quote from the Nuppin-master...and he gave a link to a pack of 25...


SCREW: SS set screw, cup point, hex/socket drive (18-8, A2, or 304). M2x0.4 and 2.5mm length (that's an M2 screw that's 2.5mm long and has a 0.4mm thread pitch)

and a note: M2 screws with .4mm pitch are very common for atomizer set screws. Likely they will work in most atties (all of the ones I happen to have owned).

Hey Nuppin fans!
I bought a V2 in the classies a couple years ago.
It was missing a side grub screw.
After talking to Peter, I think he said I needed a M2 x 2.5mm screw.
Finally ordered some from FT.
Went to try them...no go?
They look to be the same size, but the threading on the FT ones are coarser.
The originals seem to have a fine thread.?
Are there different threadings, or a FT screw up?
What size do I need? and where to get them?
Thanks!

 

[puffon]

Probably a Fasttech quality thing - that's the right size... Here is a direct quote from the Nuppin-master...and he gave a link to a pack of 25...


SCREW: SS set screw, cup point, hex/socket drive (18-8, A2, or 304). M2x0.4 and 2.5mm length (that's an M2 screw that's 2.5mm long and has a 0.4mm thread pitch)

and a note: M2 screws with .4mm pitch are very common for atomizer set screws. Likely they will work in most atties (all of the ones I happen to have owned).

Thanks Train!
Will put together a McMaster shopping list.
They sell better quality grubs. (made in the Philippines)

 

[ckquatt]

That's the exact ones I bought a while back! Still using the same 3 I replaced for over a year now. Really good quality set screws!