Nuppin'
- Thread starter Spydro
- Start date
- th_trl_thread_readers 0
- Status
Thank you also {a very nice someone sent me a pm as well
}I could not get checked out though. So I called and spoke directly to someone there who was very nice and helped me out. He has many pieces but all are not ready yet, so he can only put so many up at a time on the site. There should be plenty to go around for awhile. Get 'em while they are HOT
^good to know but my weekly productivity is going way down gonna spend the next few days pressing f5!
I could not get checked out though. So I called and spoke directly to someone there who was very nice and helped me out. He has many pieces but all are not ready yet, so he can only put so many up at a time on the site. There should be plenty to go around for awhile. Get 'em while they are HOT
I certainly don't need anymore drip tips, have dozens I don't even use. But I bought 3 of them anyway to see if all the hype is just hype or they will be good enough to replace some of my DT's that I do use. I expect they will be since my limited experience with them was quality gear... (I still have a bunch of their black Delrin ProRings from my ProVari days although most are unused, that IMO are way better for the blacked out PV top caps than their replacement black metal ones that could scratch the caps).
I've seen it written and now I'm a believer. Today I rebuilt 1 of my nuppins to .8 ohms - I added a wrap of 29 ga to each coil. Seems that my traditional 8 wrap build was quite a bit warmer in the nuppin than I liked.
Even the 9 wrap was warmer than I like. So I rebuilt the other two in rotation to 10 wraps. I also lowered the coils so the tops are dead in line with the bottom of the air intakes.
It also seems like nuppins like a SLIGHTLY and I mean slightly (like a hair slightly) thicker wick than my other dual coil attys.
I was rockin before now I'm really freakin rockin. 0.9 ohm builds will do wonders for battery life vs 0.6 I'm guessing. I also noticed that I was most of the way thru the 6ml bottle 1/2 way thru the day.
The higher resistance build oughta help that too.
Seems this smaller diameter Atty is more efficient than the larger 22mm?
Even the 9 wrap was warmer than I like. So I rebuilt the other two in rotation to 10 wraps. I also lowered the coils so the tops are dead in line with the bottom of the air intakes.
It also seems like nuppins like a SLIGHTLY and I mean slightly (like a hair slightly) thicker wick than my other dual coil attys.
I was rockin before now I'm really freakin rockin. 0.9 ohm builds will do wonders for battery life vs 0.6 I'm guessing. I also noticed that I was most of the way thru the 6ml bottle 1/2 way thru the day.
The higher resistance build oughta help that too.
Seems this smaller diameter Atty is more efficient than the larger 22mm?
Last edited:
My .44Ω coils in my Nuppin' vape as warm if not warmer than the .33Ω coils I have in one of my Mephisto's. My guess would be the internal dimensions of the atty... I think I am running 24g in both of them right now. I might change the Nuppin' over to either 26g or twisted 29g for the next go round, though I really don't see that happening anytime soon. Those coils have been in it for over 2 months now with the same RxW as well and still rockin' it out... The only downside is I have tried on occasion to use a SS drip tip on it, but it just gets too hot too quick so I have to use a delrin tip on it.
Yeah, I can only imagine. My SS DTs were getting warm at double your resistance. Now it's perfect
I find the Nuppin' hits a good .1ohm harder and hotter than most other atties. I'm running the highest resistance in them of all my dual setups (.55ohms). I suppose I could lengthen and/or delrin the dt's but I'm digging the slightly longer bat life.
I've never used 24G (or 26G for that matter) but have them both. In the next days I will be building some 24G/RxW coils at .5 ohm for a gal pals KFL's and send them to her. While at it thought I'd try building some 24G/26G .5 to 1.7 coils for the Nuppin's as well. Right now my Nuppin's are running 28G single and dual micro/twisted at .5-1.23 with RxW/KGD depending on joose... and they are getting it done very fine. But I want to finally see firsthand what all the hype is about those other wires. Also see some play time coming using some of my ribbon wires with RxW in the Nuppin's. The hard part is removing a build that is working so well in them.
Last edited:
28g 10 wraps around the second to smallest gizmo rod dual coil - .7ohm but made a switch today from my traditional rayon/readyxwick...went to Sephora and bought some Shiseido (like KGD) and OMG - no cotton taste! I LOVE this stuff! Because I used rayon for so long I'm in the habit of stuffing as much wicking in the coil as possible but yes, Russ, I know you are right...Nuppin works SO well with a packed load of wicking however it has yet to gurgle or leak - and I'm a habitual squonker.
I have played with some MM wire 4/5 wraps (~.63 ohm) and it hits pretty good and will heat up a dt in no time. I also have one that is dual 8 wrap 28ga 1/16 coils (~.45 ohm) and that is a dragon. The router drip tip gets hot quick so I have to use a longer one. I just built one with a single 1/16 8 wrap 28ga (~.9 ohm). It is a nice clean vape with good flavor if I close off the air a bit. The router dt is ok on this build....lol
I have some 26ga that I need to play with as well and see what happens. Maybe this weekend!!!
Try out the 26. It doesn't get quite as hot as 28 at the same ohms. That will reduce heat on the drip tip. The steam-engine calc is a very good tool for seeing where you are and what you can get with different gauge wires.
I think I should have lowered my nic instead of raising my ohms.....Just playing around with different builds I went through 4ml of juice in a couple of hours and now I am ready to sleep this buzz/headache off.
I just ordered another 250' of 29 from temcoindustrialpower. Lightning fast heat up and cool down. I just haven't found another wire that checks all the boxes like 29 at the ohms / wrap count / inner diameter I like to run.
Dual-coil at .8 seemed too hot in the Nuppin compared to the Odin for me due to the smaller chamber. I wanted the same amount of full vapor and flavor the duals give me. I made my first twisted coil that came in at .9 and ran it alone. OMG, the vapor is the same as I got in the Odin set up as a dual coil and the flavor made me actually think I was squonking juice up my drip-tip. It really is that good with a single twisted coil. 6 wraps of 29g twisted.
Last edited:
What gauge did you twist together? Did you use a drill and how many strands?
Pauly3
Sent from my iPhone using Tapatalk
2 strands 29g. About 4 feet folded over in half. Put looped side in drill with Allen key in the chuck. Held other with a pliers and slowly twisted with drill. Then faster til it broke. Used second smallest mandrel in gizmo and hand wrapped.
Nice. I do exactly the same with 28 gauge in a Chalice III. Great vape.
- Status
