Odysseus Illustrations
- Thread starter Para
- Start date
- th_trl_thread_readers 0
- Status
I am getting there. Here are the Assembly Models for: Odysseus (Short Mode), Odysseus (Short Mode - GGTS Base), Odysseus (Full Mode), Odysseus (Full Mode - GGTS Base) and Odysseus (Dripping Mode).
I still need to do Assembly models for: Odysseus (UFS Mode), Odysseus (510 Atomizer Mode), Odysseus (E2 Mode). Will also need to model an E2 basic carto for use in the E2 mode.
You may notice that there is an O-Ring above the cone of the mouthpiece in the "Short Mode - GGTS Base" and above the shoulder on the mouthpiece in the "Full Mode - GGTS Base". That is a 9 x 2mm and is needed from my experience to prevent the cone from completely unscrewing from the ceramic housing when using the GGTS Base. This is due to the ceramic housing screwing further into the base than the normal 510 base.
Odysseus (Short Mode)
Odysseus (Short Mode - GGTS Base)
Odysseus (Full Mode)
Odysseus (Full Mode - GGTS Base)
Odysseus (Dripping Mode)
Every timke I see your work Zor, I am amazed. Thank you for what you do for us. YOu are an invaluable asset to the GG community!
There is a thread specifically for Zoranth's illistrations.
http://www.e-cigarette-forum.com/forum/gg/240530-gg-product-illustrations.html
Also I am sure they will be added to the Wiki once they are done.
Ariel and I are just standing by waiting for this illustration to add them to the wiki.....
Great illustrations as always, Zoranth!
Thank you.
I think Zor ahould be Beta VV GG dude.........
I feel like I owe you something, dude........
I feel like I owe you something, dude........Zor is a permanent "tester" for all GG products ripple. He makes the designs and he needs to have the pieces in his hands
Took a while to do this and I hope I got it right. I think I did anyways
Had to strip down a new CE2 in order to model all of the parts for it Lol
Odysseus (Full E2 Mode)
Had to strip down a new CE2 in order to model all of the parts for it Lol
Odysseus (Full E2 Mode)
Last edited:
Why is the O-ring needed on top of the mouthpiece stop flange in both short/long mode when using the GGTS base?
Does that basically extend the stop because of the increased depth of GGTS base, as opposed to the 510?
Does that basically extend the stop because of the increased depth of GGTS base, as opposed to the 510?
The Insert goes further into the GGTS base than it does the standard 510 base. So the O-Ring is used to extend the top of the shoulder on the mouthpieces to prevent the mouthpiece from coming off when you try to adjust it to it's maximum.
Note: That O-ring did not come with the kit but I use a 9x2mm and it works fine.
Note: That O-ring did not come with the kit but I use a 9x2mm and it works fine.
Here are two more. Got two more models (510 - GGTS Base and Dripper in UFS) to do then I can start working on the Exploded Diagrams.
So, please be patient there was quite a lot to do this time
Odysseus (E2 Full Mode - GGTS Base)
Odysseus (510 Full Mode - GGTS Base)
So, please be patient there was quite a lot to do this time
Odysseus (E2 Full Mode - GGTS Base)
Odysseus (510 Full Mode - GGTS Base)
Last edited:
Could you do a cartomizer mode? if it's even possible.
Last time I did it I just put the 510 mode in big mode and let the cartomizer go up through the top and used my own drip tip. I used the o-ring on the top of the cartomizer to seal it up with the top piece. I don't know why it leaked so badly. It wasn't a couple drops, it leaked until the tank was empty through the bottom.
Last time I did it I just put the 510 mode in big mode and let the cartomizer go up through the top and used my own drip tip. I used the o-ring on the top of the cartomizer to seal it up with the top piece. I don't know why it leaked so badly. It wasn't a couple drops, it leaked until the tank was empty through the bottom.
Silent, I do not know and I do not have a Carto to try with. Lol, never have had a carto
a smaller hole on carto was required as I see it silentt. The tank is big so liquid gives a big preasure on carto
- Status
