Official DiscountVapers.com Thread
- Thread starter gormly
- Start date
- th_trl_thread_readers 0
- Status
Happy Birthday Eric!! 
Happy Birthday to my friend who sells me vaping stuff!!!! Hope Jamie and the boys treat ya like a king today!
How often can the eVod coils be cleaned with vodka? How would I clean the eVod clearomizers?
I haven't cleaned any of them daily, but I would guess you could
I clean the eVod heads at least once a week, or more often if I change flavors. I clean the clearo portion with a small bottle brush (from the $ store, no less ) or a q-tip and dish soap. HTH
When I clean the coil heads with vodka, how long should I let them soak? Can I keep reusing the coil heads after cleaning them indefinitely?
Happy Birthday Eric!!
Now that is a picture!
oh my that is funny, I have the same problem with my DVR
Thanks for all the birthday wishes folks!
wouldn't you know it DHL picks today of all days to show up at 7PM! Had to wait to go to dinner~!
Hello?? Is this thing on???
Good afternoon Stoney and all thank God this was only a 3 day work week, and thank God tomorrow is Friday. I am completely wiped.
thank God this was only a 3 day work week, and thank God tomorrow is Friday. I am completely wiped.Hiya Zooker! Welcome back to schoolGood afternoon Stoney and all
Maybe you're ready for some relaxation time in that new bathroom? A nice bubble bath perhaps 
New DV Product...
The DV BCC Clearomizer
This is a brand new type of clearomizer with an integrated non removable drip tip and NO ML markings on the side, it is completely see through on entire unit. The center tube is molded to the drip tip with a full flute from the sealed coil to the top. Very unique looking clearomizer. And because it has our name on it, it's inexpensive unlike other brand name clearomizers. The DV BCC accepts it's own BCC Coil replacements and can even use Kanger Evod/Protank coils as well (see note below on that)
Capacity: 1.6ml
Threading: eGo threaded, will fit on all ego devices and most 510's (may need an adapter)
Height: 75.60mm
Diamter: 14.25mm
Also Unique to other bottom coil clearomizers.. our coil heads go up to 4.0ohms! The DV BCC has replacement coils in 1.8ohms, 2.4ohms, 2.8homs, 3.2homs and 4.0ohms
Tips on Usage:
Clean out the plastic part before first use, remove the base, rinse it out with water, I have found the initial taste is better after I do this, rinse it, let it dry.
Also, after you fill it (the first time) let it sit for a moment for the wicks to saturate.
Eric's Review:
This is my product so while I can review it, you must consider a little bias here. I like it, I love the non markings, looks cool. However there is a small drawback to an entirely clear clearomizer, and that is condensation. Condensation happens when warm air meets cooler air and it deposits the water vapor from the vape into the center tube and drip tip, so, while vaping this has the look of "bubbles" in the center. Perfectly normal, except now you can see it. This unit can accept kanger coils BUT, you have to slightly work it in, press down slightly while twisting it on, and when twisting it off go slow. The vape is good, nothing earth shattering but also not poor like some others on the market, I tested an evod coil in this and the difference was minimal with the DV giving a slightly harsher taste (maybe because it was new, seemed better after first fill). At 2.5 ohms I liked the evod slightly better, but with the 1.8 I liked the DV BCC better and there is not 3.2 or 4.0ohms to compare on the eVod and with the huge price difference, the DV wins!.
Also I am VERY hard on my drip tips, I can crack a T2 drip tip in an hour.. this one so far.. no issues, it's looks really fragile but it's not. You may crack not sure how strong your jaw is but for me.. so far so great!
These are at a special price right now and I plan to keep it low if it does really well
There are other pics on the website.
The DV BCC Clearomizer
This is a brand new type of clearomizer with an integrated non removable drip tip and NO ML markings on the side, it is completely see through on entire unit. The center tube is molded to the drip tip with a full flute from the sealed coil to the top. Very unique looking clearomizer. And because it has our name on it, it's inexpensive unlike other brand name clearomizers. The DV BCC accepts it's own BCC Coil replacements and can even use Kanger Evod/Protank coils as well (see note below on that)
Capacity: 1.6ml
Threading: eGo threaded, will fit on all ego devices and most 510's (may need an adapter)
Height: 75.60mm
Diamter: 14.25mm
Also Unique to other bottom coil clearomizers.. our coil heads go up to 4.0ohms! The DV BCC has replacement coils in 1.8ohms, 2.4ohms, 2.8homs, 3.2homs and 4.0ohms
Tips on Usage:
Clean out the plastic part before first use, remove the base, rinse it out with water, I have found the initial taste is better after I do this, rinse it, let it dry.
Also, after you fill it (the first time) let it sit for a moment for the wicks to saturate.
Eric's Review:
This is my product so while I can review it, you must consider a little bias here. I like it, I love the non markings, looks cool. However there is a small drawback to an entirely clear clearomizer, and that is condensation. Condensation happens when warm air meets cooler air and it deposits the water vapor from the vape into the center tube and drip tip, so, while vaping this has the look of "bubbles" in the center. Perfectly normal, except now you can see it. This unit can accept kanger coils BUT, you have to slightly work it in, press down slightly while twisting it on, and when twisting it off go slow. The vape is good, nothing earth shattering but also not poor like some others on the market, I tested an evod coil in this and the difference was minimal with the DV giving a slightly harsher taste (maybe because it was new, seemed better after first fill). At 2.5 ohms I liked the evod slightly better, but with the 1.8 I liked the DV BCC better and there is not 3.2 or 4.0ohms to compare on the eVod and with the huge price difference, the DV wins!
.Also I am VERY hard on my drip tips, I can crack a T2 drip tip in an hour.. this one so far.. no issues, it's looks really fragile but it's not. You may crack not sure how strong your jaw is but for me.. so far so great!
These are at a special price right now and I plan to keep it low if it does really well
There are other pics on the website.
That sounds absolutely heavenly, if only I could con one of the dogs into scrubbing the tub for me first!
Nice Eric, I'll have to check those out. Are the BCCs polycarbonate? And...are you biting on your drip tips?!? You've got some strong teeth 
Put some soap on one of those little dogs and scrub the tub...2 birds with one stone, so to speak, a clean dog and a clean tub
Nice Eric, I'll have to check those out. Are the BCCs polycarbonate? And...are you biting on your drip tips?!? You've got some strong teeth
Yes Poly.. but I was told it is a "new" poly that resists cracking and etc (still do not recommend the harsher liquids) which is why I said "ok" to it.
and so far I have really chomped down on it, just now, so hard it hurts my teeth a bit..
but get this.. Just took out a wrench (small hand held not too much leverage) and cranked down on the tip.. DID NOT BREAK! It deformed a bit then "sort" of went back into shape. so then spun it 1/4 tried again, same thing. Next I stuck the wrench in the middle of the clearomizer and it DID NOT BREAK. Granted I wasn't going nutso but I was clamping down hard enough to leave wrench teeth marks.. so yea, this is a strong sucker
edit I just put pure cinnamon, orange and cola in three of them.. will report back what happens..if those don't kill it.. well this is a super win
Last edited:
Thanks.Yes Poly.. but I was told it is a "new" poly that resists cracking and etc (still do not recommend the harsher liquids) which is why I said "ok" to it.
and so far I have really chomped down on it, just now, so hard it hurts my teeth a bit..
but get this.. Just took out a wrench (small hand held not too much leverage) and cranked down on the tip.. DID NOT BREAK! It deformed a bit then "sort" of went back into shape. so then spun it 1/4 tried again, same thing. Next I stuck the wrench in the middle of the clearomizer and it DID NOT BREAK. Granted I wasn't going nutso but I was clamping down hard enough to leave wrench teeth marks.. so yea, this is a strong sucker
LOL, going at it like that sounds like something I would do
- Status
Similar threads
- Locked
