Official ProVari 3 Thread - P3

[Bronze]

I'm really thinking of buying a p3, but have a few questions. basically I would only want to run it in 18350 as I like small setups. I also vape my v4's at around 1.3-1.4 ohms at around 18w.

battery life expectancy?
iq issues? been reading a lot of reports of people having issues with the p3.

I don't mind carrying around a few batteries, but I've read reports of 40 puffs on a 18350. I'd be changing a battery every 20mins at that rate lol

I use an 18350 on a 1.5 ohm KFL and I burn 3 mls of 70/30 blend on a single charge using my P3.

 

[Bronze]

by the way, this is by far the friendliest part of the forum I've come across so far!

You wouldn't have said that a couple nights ago.

 

[DPLongo22]

You wouldn't have said that a couple nights ago.

I do not recall that...

 

[oplholik]

I use an 18350 on a 1.5 ohm KFL and I burn 3 mls of 70/30 blend on a single charge using my P3.

What voltage do your batteries read when you take em out?

 

[raitizz]

What voltage do your batteries read when you take em out?

My AW 18350 800mAh read around 3.50V every time. Plus/minus depending on the power I ran them on.

R

*via Tapatalk

 

[redordead]

Thanks - good to know.


-Sent via Tapatalk

This is my vaporshark. peeled right off in days. awful device IMHO.

 

[redordead]

That's the thing with the ProVari. It works. If it doesn't work it's repairable. You pay up front then you are just buying batteries, which are relatively inexpensive.

People make the arguement that buying cheap mods saves you money. Sure. Maybe. But they aren't generally accurate or as reliable and safe. I was reminded of this by that thread about the nonstop auto-firing iStick. I have Four of those little suckers. Cheap. Fun. But not very accurate and subject to foibles.

I don't want a mod with foibles. I want a girlfriend with foibles. Now that's merely charming. Mods with foibles? Not so much.

If I was on the other side of the Atlantic, I'd probaly be using a Semovar, just to save on repairs shipping.

It's a very good device too.

ProVape has pulled ahead with the P3 though atm imo.

I live in Italy now, but I wouldn't consider a semovar. 15w isn't enough for me. I also don't like the look of the device. I really like the look of the P3. apart from the diameter that is...you can't have it all though eh!

 

[Mowgli]

Seem bit pricey...

Colorful Silicon Seal Ring Set for SUBTANK Mini (50-Set) - $7.24

R

Pricey for a $33 Sub mini + 5 different colored sets of o-rings?

 

[oplholik]

If you don't want that many, look here.

Subtank O-Rings - Kanger Subtank - Kangertech - Clearomizers Tanks

 

[raitizz]

Pricey for a $33 Sub mini + 5 different colored sets of o-rings?

Oh, the tank is included?? Then pardon me
Niiiice price.

R

*via Tapatalk

 

[Juggernaut666]

This is my vaporshark. peeled right off in days. awful device IMHO.

Polish that thing up, they actually look pretty cool polished, our send it to someone for cerakote..... saw this one posted fb the other day.

 

[redordead]

I actually sold it on eBay yesterday. much rather spend the money on a p3. I've gone off box mods.

however, that does look really, really good!

 

[Juggernaut666]

I'm actually looking at having both of my P3s custom cerakoted. Harley Quinn and Joker themed.

 

[DPLongo22]

This is my vaporshark. peeled right off in days. awful device IMHO.

Are you serious????

 

[raitizz]

I dunno... The VS would be one of the boxmods I'd consider to aquire.

R

*via Tapatalk

 

[redordead]

I'm actually looking at having both of my P3s custom cerakoted. Harley Quinn and Joker themed.

Where does one get that done?

 

[redordead]

Are you serious????

yep. within 4 days of usage 50% of the finish had peeled off. It was so bad, that just putting on a sharkskin would take the finish off. There were small patches where the paint remained. The finish on the doors held up though.

 

[jwbnyc]

redordead:

One thing you want to check is if the P3 will fire at 18W with your ohms.

 

[raitizz]

redordead:

One thing you want to check is if the P3 will fire at 18W with your ohms.

It will. Red stated he vapes around 1.2-1.4 ohms.
R

*via Tapatalk

 

[Bronze]

What voltage do your batteries read when you take em out?

3.3 volts...when it says "empty".