Official ProVari Radius Thread - Part 2

[Bronze]

I'm happy to find that there are now more upgrade centers in the Greater Los Angeles Area and one is roughly 1/2 hour away from me -- or two hours, depending on traffic!

I have a feeling both the P3 and Radius upgrades were only made available today, so the retailers may not have known about it until very recently.

I lived in an apartment in a heavily congested area when I was young. You could stand in the parking lot and see the grocery store but it would take 15 minutes to drive there.

 

[Bronze]

You are more than welcome to do that.

ProVape should add you to their list of authorized dealers.

 

[rbrylawski]

I was with you until you claimed it is better than an xtar. I don't believe you.

Sir Rod does not lie. Nope. Nevah. The only advantage the xtar has (if'n you can call it an advantage) is you can watch it do its magic for hours (which you ain't gettin' back nethuh) as opposed to the seconds you can watch your Radius update.

 

[rbrylawski]

ProVape should add you to their list of authorized dealers.

Or just put me on their payroll!

 

[Vape360]

That must be why my Radius battery is dead after a week of no use, due to the P3 to 510 adapter being stuck on my tank (still haven't managed to get it off). Battery was fully charged, and after reading the sleep mode post, just tried turning it on, and it's completely dead. Guess I'll upgrade!

PS - @Vape360 - Any thoughts on a single-piece P3 to 510 adapter with integrated beauty ring? Seems it would solve the tank locking problem.

I'll check with the team on this one.

 

[ENAUD]

I'll check with the team on this one.

I would buy four of those one piece rings, no make that five I have experienced the locked rings and would happily change all of my P3 threaded devices over to a new type of P3/510 interface, if you folks choose to make one...Please!!

 

[HBcorpse]

I'll check with the team on this one.

I would buy four of those one piece rings, no make that five I have experienced the locked rings and would happily change all of my P3 threaded devices over to a new type of P3/510 interface, if you folks choose to make one...Please!!

Same!
I haven't experienced it *knocks on wood*...but I've always wanted a single piece.
I'd love to install a few of them on my tanks directly, so I can just pop them on/off the P3 and go!

 

[ENAUD]

Same!
I haven't experienced it *knocks on wood*...but I've always wanted a single piece.
I'd love to install a few of them on my tanks directly, so I can just pop them on/off the P3 and go!

That, is a grand idea!

 

[HBcorpse]

That, is a grand idea!

Why thank you!
It will only work for non-bottom fill tanks...my KFLs are gonna be outta luck, as I need to access their fill screws.
But I've got some other tanks that wouldn't mind having a single piece P3-510/beauty ring tightened on and never taken off!
Then again, if I could find a decent top fill system for a KFL, I'd just go ahead and weld the ring to the bottom and voila! P3 KFL!

 

[JohnD0406]

Same!
I haven't experienced it *knocks on wood*...but I've always wanted a single piece.
I'd love to install a few of them on my tanks directly, so I can just pop them on/off the P3 and go!

Well, in your case, you might be better off with the 2-piece design. You can use the beauty ring to lock the P3 adapter to the tank, and then you don't have to worry about the adapter coming off, and you have a P3 tank!

 

[HBcorpse]

Well, in your case, you might be better off with the 2-piece design. You can use the beauty ring to lock the P3 adapter to the tank, and then you don't have to worry about the adapter coming off, and you have a P3 tank!

:headbangs harder:
[emoji1591][emoji1591][emoji1591][emoji1591]

 

[ENAUD]

Either way, at some point I plan on socking some extra rings away into my parts bin.

 

[StealthyTX]

I would buy four of those one piece rings, no make that five I have experienced the locked rings and would happily change all of my P3 threaded devices over to a new type of P3/510 interface, if you folks choose to make one...Please!!

@Vape360 As will I!!!!!! Five of em!

 

[AlphaGuitarist]

@stanleybb50 Ooooooh, a new RTA??? How does the Calix compare to the KF4?

 

[jwbnyc]

I like pretty things.

I do tend to be compulsive like that but 2 Goldmember edition 2.5's were a no brainer and my Signature, P3 and Radius were just stupid cheap over the holidays.

I can't see myself owning 10 or more Provaris (don't write down that I said that), but a second P3 for a good price would be of interest.

 

[jwbnyc]

Why thank you!
It will only work for non-bottom fill tanks...my KFLs are gonna be outta luck, as I need to access their fill screws.
But I've got some other tanks that wouldn't mind having a single piece P3-510/beauty ring tightened on and never taken off!
Then again, if I could find a decent top fill system for a KFL, I'd just go ahead and weld the ring to the bottom and voila! P3 KFL!

This is mine:

Custom Top Cap for Kayfun - made by InTaste - InTaste

 

[billsfande]

Just pulled the trigger on a ghost white with a p3 kabuki. This will be my fourth Provari to go along with my white and black fade v2.5, zombie mini and zombie p3. Was hoping that they would come out with a zombie radius but that will just give me a reason to add number 5 to the collection.

I will probably use the kabuki on my p3 zombie. I got a hurricane rta a couple months ago and think it will be perfect with the radius.

Can't wait. Lol

 

[rbrylawski]

This is mine:

Custom Top Cap for Kayfun - made by InTaste - InTaste

I have one just like this (could even be the same thing). But I didn't ever get the hang of it as no matter what I did (turn it upside down, cover the air hole, turn it back up, etc), juice still leaked while top filling.

 

[JD53]

Why thank you!
It will only work for non-bottom fill tanks...my KFLs are gonna be outta luck, as I need to access their fill screws.
But I've got some other tanks that wouldn't mind having a single piece P3-510/beauty ring tightened on and never taken off!
Then again, if I could find a decent top fill system for a KFL, I'd just go ahead and weld the ring to the bottom and voila! P3 KFL!

The best top fill for a KFL is a Kayfun 4!!

 

[HBcorpse]

Calix v2 Elegance P3
Calix v2 Cage P3
Calix v2 Color edition
are now in stock!