Official ProVari Radius Thread - Part 2

[WillyZee]

again, 14 hours between posts

Sent via iPhone

 

[rbrylawski]

Hey there!!!


Sent from my iPhone using Tapatalk

 

[AlphaGuitarist]

I think most people are happy with their Radii, so this thread kind of died down.

 

[Bronze]

The P3 thread is dead too. Product-specific threads have a shelf life. This is why there is a ProChat thread where all Provape topics are welcome.

 

[Slodog79]

Question????

The battery meter, currently I vape a KV4 with a 1.3 ohm build. The battery meter only stays full for the about the first 10 vapes, then starts to drop off. I chain vape for the most part, if I let the mod rest I notice that the battery level will slightly rise. Is the normal? Also I noticed that as the battery drains, it will allow me to vape for a good while with the battery meter showing all most empty. Is this the norm? Eventually the button flashes red and back on the charger it goes.

 

[rbrylawski]

All normal.


Sent from my iPhone using Tapatalk

 

[Slodog79]

Thank you sir

 

[rbrylawski]

You're welcome!


Sent from my iPhone using Tapatalk

 

[ENAUD]

Just did a battery swap in my Radius, 1:17...not so bad

Empty battery reads 3.2V

 

[USMCotaku]

Just did a battery swap in my Radius, 1:17...not so bad

Empty battery reads 3.2V

I don't know what some were complaining about....I've got the battery swap down to about 15 seconds. Its really not that bad to do.

 

[HBcorpse]

I don't know what some were complaining about....I've got the battery swap down to about 15 seconds. Its really not that bad to do.

I don't own one yet, but...RIGHT???

All these people complaining about a "complicated battery exchange" when they don't even realize the beauty of the fact that you CAN change the battery.
So many box mods in this class have CAPTURED batteries, which are either non-serviceable, or have to be sent back to their manufacturer to be swapped...for a price!

Some people just aren't happy unless they're complaining! And that's ok! I'll let them do them...while I enjoy my Stealth Radius!

 

[ENAUD]

Here's hoping you get your wish of a stealth version HB

 

[HBcorpse]

Here's hoping you get your wish of a stealth version HB

I am 100% sure that it is not a matter of if, but when…

 

[access0denied]

The mothership needs to announce a new firmware update. That will create some chatter between us.

 

[jwbnyc]

I don't know what some were complaining about....I've got the battery swap down to about 15 seconds. Its really not that bad to do.

I think the biggest problem is the screws aren't attached to the bottom cap.

 

[BreSha6869]

I think the biggest problem is the screws aren't attached to the bottom cap.

Bingo. That would solve the problem completely.

Not complaining, but it is not a matter of "if" it is a matter of "when" I will lose one of the screws.

 

[Nailz]

Bingo. That would solve the problem completely.

Not complaining, but it is not a matter of "if" it is a matter of "when" I will lose one of the screws.

Good job they sell replacements then - ProVari Radius Stainless Steel Screws

 

[BreSha6869]

Good job they sell replacements then - ProVari Radius Stainless Steel Screws

Already on that.

 

[HBcorpse]

First thing I do, once my Stealth Radius arrives, is...
Go to my local nuts'n'bolts shop, and buy me the appropriate size of these:

They make them thin enough I'm sure they'll fit inside the cap.
This will effectively lock the bottom cap screws onto the cap, so they won't get lost!

 

[ENAUD]

First thing I do, once my Stealth Radius arrives, is...
Go to my local nuts'n'bolts shop, and buy me the appropriate size of these:

They make them thin enough I'm sure they'll fit inside the cap.
This will effectively lock the bottom cap screws onto the cap, so they won't get lost!

I was actually kinda surprised that Provape wasn't all over a retention clip of some sort with this particular design. Maybe we'll see an updated version at some point...