Ok, guys.....

[imeothanasis]

Nice! Where can I take it in to get shined? Any recommendations?

any shop with a lathe or a shop that sells jewels buddy

 

[Zaiden]

Can you give me the pricing for the following so I can determine if I should shine up my GGTS or just buy a new one?

1) GGTS w/ GGTSAFS combo (you mentioned there would be some sort of discount if both were purchased)
2) GGTSAFS
3) updated bottom cap
4) aluminum telescoping center

Side Note: I bought the upgraded fuse kit and I found a problem with it. I was getting constant misfiring with my GGTS so I took it all apart and cleaned every single piece thoroughly. I was still getting misfiring. I then took off the fuse kit and replaced it with the original bottom cap/spring and low and behold I have massive vapor hits every time. I checked the fuse and it was not coiled back or anything. My thoughts are that the fuses are causing very poor conductivity and even when fully operational are still not even close the amount of vapor hits when using the normal bottom cap. Any thoughts on this? I'd like to benefit from the safety of the fuse kit, but not at the expense of my vaping experience.

 

[HoPeFuLLL]

My thoughts are that the fuses are causing very poor conductivity and even when fully operational are still not even close the amount of vapor hits when using the normal bottom cap. Any thoughts on this? I'd like to benefit from the safety of the fuse kit, but not at the expense of my vaping experience.

Had a similar issue which putting a new fuse in fixed although the old fuse metered fine. Was confusing on a new unit. All fine with fuse now though.

 

[Zaiden]

Yea, I did the same thing. However, I find that the fuses last about 2 weeks and for some strange reason just stop working. Even with a fully working fuse it still doesn't compare to the standard bottom cap. I think this product might need some redesign work or maybe Imeo can provide some insight.

 

[imeothanasis]

Can you give me the pricing for the following so I can determine if I should shine up my GGTS or just buy a new one?

1) GGTS w/ GGTSAFS combo (you mentioned there would be some sort of discount if both were purchased)
2) GGTSAFS
3) updated bottom cap
4) aluminum telescoping center

Side Note: I bought the upgraded fuse kit and I found a problem with it. I was getting constant misfiring with my GGTS so I took it all apart and cleaned every single piece thoroughly. I was still getting misfiring. I then took off the fuse kit and replaced it with the original bottom cap/spring and low and behold I have massive vapor hits every time. I checked the fuse and it was not coiled back or anything. My thoughts are that the fuses are causing very poor conductivity and even when fully operational are still not even close the amount of vapor hits when using the normal bottom cap. Any thoughts on this? I'd like to benefit from the safety of the fuse kit, but not at the expense of my vaping experience.

I cant tell you much about prices now Zai, but soon I will be able to tell you.
About fuse. You had a bad contactivity between fuse's spring and internal bottom of the brass axis. You can sand spring and the bottom of the axis and you will see that vapor will come to normal levels again

 

[imeothanasis]

Yea, I did the same thing. However, I find that the fuses last about 2 weeks and for some strange reason just stop working. Even with a fully working fuse it still doesn't compare to the standard bottom cap. I think this product might need some redesign work or maybe Imeo can provide some insight.

It stopped working for the same contactivity reason. Sand the parts as I mention above and it will work like new again. Exept of course you had a shrinked spring from a short

 

[Zaiden]

Not sure I'm understanding what part needs sanding. Can you give me a better worded explanation or better yet a picture with some arrows?

 

[imeothanasis]

of course Zai

Imageshack - 80079970.jpg

 

[Stormynights]

Not sure I'm understanding what part needs sanding. Can you give me a better worded explanation or better yet a picture with some arrows?

When I put mine together I sanded the spring because I was having a little problem. I haven't had to touch it since.

 

[Zaiden]

Thanks for the picture...that helped a lot. However, how would you suggest I clean the inside of the brass tube? Also, what kind of sanding paper (grit level, etc.) I should use to sand the spring and contact point?

 

[imeothanasis]

Thanks for the picture...that helped a lot. However, how would you suggest I clean the inside of the brass tube? Also, what kind of sanding paper (grit level, etc.) I should use to sand the spring and contact point?

a more than 1000 sand paper is ok Zai. As for the way to clean it, you can put inside the axis a sand paper on a thin pen or something like that

 

[imeothanasis]

And dont forget to extend the spring. Make it big, no problem

 

[Deetz]

#4, for me, please.
... I hope Imeo makes enough in the first run, I'd be really bummed out if they sell out before I order one. Maybe a poll should be taken?


I tried the free version of Tapatalk for Android and it wouldn't let me submit posts. Does the free version for iOS let you post? If you have the paid version, for either OS, you can edit your signature line.

I have the paid version, but never noticed the signature. Thanks for the info!