Polishing RBA expromizer NEED advice

[S1DD]

Hi guys,
I bought the expromizer a bit too early and now stuck with the 1.1 version, normally I won't even give a dam but the 1.2 have a polish version which look
pretty cool .... Now I could easily polish the exterior to make it shine like chrome with autosol stainless steel polisher but I'm worried about polishing the interior mechanism (the parts that could be seen throught the glass) cause it will touch the ejuice which will go into your body.

Any advice on how to polish the interior parts of the mechanism without resorting the chemical compound will be appreciated.
PS if there is a know compound that is safe to be used on the interior parts of the atomiser please post it as well.

 

[Warpigs]

Welcome to ECF, I have no clue but I'm sure someone will have an answer for ya

 

[dynoman2002]

Welcome!
I have polished many interior pieces and tips that come in contact with juice. Just make sure after you poish to clean each piece with soap and water, then go over them with rubbing alcohol. I clean after polishing until i cant smell the compound anymore and vape away.

 

[S1DD]

May I know what compound brand you used to polish your atomiser
And been googling about polishing and read that I require sand paper of different grain to achieve a chrome look on stainless steel, is it really necessary?

 

[dynoman2002]

Absolutely! I use blue magic metal polish cream. I personally only use 600 and 1000 grit sand paper in conjuction with my dremel and polishing wheels.

Before polish

After polish and i also polished the stillare

 

[S1DD]

Thx for the advice dude I'm going to try it after getting the sand papers, it's better to pay a few buck for the sand paper than buying the same atomiser just for its aesthetic.
Wish me luck...seriously do it with my DIY skill I'll need all the luck, blessing and other paranormal forces.... to succeed

 

[dynoman2002]

No luck needed just take your time and it will come out great! Just let me know if you have any questions well get you all polished up NO PROBLEM.

 

[Susan~S]

Hello and welcome to the forum S1DD. Glad to have you here!

I especially like the "other paranormal forces"!

 

[AliasMX921]

Don't ya hate that I feel the same way about mostly all electronic things it feels like as soon as you buy something a better version comes out the next day.

 

[S1DD]

Yes yes I do after buying provari v2 , v3 came out sigh

UPDATE
I think I frack it up
The polishing went fine now my expromizer shine like chrome buuuuttt
Every time I did a dry hit it has a bit of a autosol smell, should I be worry?
And dump the liquid and re clean the thing again?

 

[dynoman2002]

Yes yes I do after buying provari v2 , v3 came out sigh

UPDATE
I think I frack it up
The polishing went fine now my expromizer shine like chrome buuuuttt
Every time I did a dry hit it has a bit of a autosol smell, should I be worry?
And dump the liquid and re clean the thing again?

Just make sure its clean there might still be a slight smell but should dissapate rather quickly. If not dump juice and clean again.

 

[S1DD]

Clean it with alcohol and dish water soap 3 times and still the taste of autosol is there
It doesn't effect the taste of the juice much but that little bit of smell really kill the vaping experience for me.

Sigh any other solution
Oh n I found that one of the rubber insulator in the expromizer smell the most like autosol ( maybe I accidentally touch it with my dirty finger )
But the smell won't go away even after dumping in alcohol straight up

 

[S1DD]

Oh yeah I had the idea of dumping it in white vinegar but... Tell me is it a dumb idea?

 

[dynoman2002]

Yea if anything wierd gets on o-rings or insulators it well smell for a minute. Just let some hot water run over it and hopefully that will dissapate the smell.

Vinegar not what i would use but shouldnt hurt anything other that it smell too. LOL