Quad Coil on RM2

[zmauls]

Madman here with another gnarly (not to mention very simple) build for the sub-ohmers of Reoville.

Quad Coil (Dual/Parallel) for RM2

• 28G Kanthal A-1
• 3/32" ID
• Total 4 x 6 wraps (1.12Ω per 1/2 coil) or 2 x 6 "double wraps" (0.56Ω per full coil)

This is the method I used to wrap - two strands of wire per coil:

In the blue corner, weighing in at...:

All screwed in:

All screwed in (cont'd):

Fired up:

Yippee:

To anyone who actually tries this build out, I hope you enjoy it.

vape on.

 

[elscorcho]

Nice plumage!

 

[Filthy-Beast]

 

[Rat2chat2]

to you on your build and that is an awesome picture of a cloud.

 

[B2L]

Love me some parallel coils, never tried dual parallels though. I'll have to give it a shot.

 

[Raynman]

Yer a sick puppy MadManZ .... Must be why yer my friend. I don't think I could go that low but it looks great.

 

[jifjifjif]

I also love parallel coils. I run them almost exclusively now. 28 gauge kanthal wrapped 4 times on a q-tip and wicked with 3 mm readyxwick. Comes in at .47.

This looks interesting. Do you have two air holes in the cap, zmauls?

 

[zmauls]

I also love parallel coils. I run them almost exclusively now. 28 gauge kanthal wrapped 4 times on a q-tip and wicked with 3 mm readyxwick. Comes in at .47.

This looks interesting. Do you have two air holes in the cap, zmauls?

Since day one, brother. I have a total of seven caps, all drilled differently. Some have four holes, some have two, but none have just one.

I believe the cap I'm using with this is 5/64" per hole. Might be 7/64". I'll check when I get home.

 

[jimkipila]

Awesome, bro! Now I gotta do it, lol. I'll let you know how it pans out later today.


Sent from my iPhone using Tapatalk

 

[zmauls]

Quick update:

The holes on the cap I was using with this build are drilled to 5/32". I would recommend around 1/8". 5/32" is a bit cool for my tastes.

 

[zmauls]

Edited the post above; I accidentally typed 5/64" before.

 

[X-Puppy]

Easier said than done, and pics to prove it. That has to be an awesome vape!

Good stuff

 

[RattlerX]

Madman here with another gnarly (not to mention very simple) build for the sub-ohmers of Reoville.

Quad Coil (Dual/Parallel) for RM2

• 28G Kanthal A-1
• 3/32" ID
• Total 4 x 6 wraps (1.12Ω per 1/2 coil) or 2 x 6 "double wraps" (0.56Ω per full coil)

This is the method I used to wrap - two strands of wire per coil:

In the blue corner, weighing in at...:

All screwed in:

All screwed in (cont'd):

Fired up:

Yippee:

To anyone who actually tries this build out, I hope you enjoy it.

Vape on.

I built a couple of these coils this morning 30ga 4 wraps around 2.5 mandrel came in at .52ohm. One in a cyclone AFC and the other in a RM4. Both vape great and the heat up time is quick. It is a juice hog but IMO the flavor is better than individual dual coils at the same ohm range.

 

[zmauls]

I built a couple of these coils this morning 30ga 4 wraps around 2.5 mandrel came in at .52ohm. One in a cyclone AFC and the other in a RM4. Both vape great and the heat up time is quick. It is a juice hog but IMO the flavor is better than individual dual coils at the same ohm range.

Awesome, brother. Glad you liked it!

 

[worseforwhere]

This setup hits hard...and I only built one side! I couldn't imagine running both and having a quad coil. I would immediately OD on nic i think.

 

[zmauls]

This setup hits hard...and I only built one side! I couldn't imagine running both and having a quad coil. I would immediately OD on nic i think.

My juice is only 2mg, and my air holes are drilled to 5/32" on both sides for this build. Glad you liked it! Care to share what kind of wire and how many wraps you used?

 

[worseforwhere]

I was I was using 28 gauge...don't remember how many wraps...looks like 6 or 7ish. It weighed in at .65 ohms.