RDA Round-Table Discussion and Lookout

[Mr.Mann]

View attachment 538650
View attachment 538651

Evolve rda.

Looks good to me.

 

[67Tele]

I'm now a BottomFeeder...

SwampPiano with NarDA. 26ga 3mm ID 1.0 ohms

 

[B2L]

I'm now a BottomFeeder...
View attachment 538807

SwampPiano with NarDA. 26ga 3mm ID 1.0 ohms

Way to jump in with both feet

Welcome to the dark side

 

[67Tele]

thanks man! The beckoning voices were strong...

 

[will s. flavoursnob]

If you decide to do that let me know. The Nar mods group is one of those damn secret groups but I can ask about getting you (and others if they want) in the group.

I would be ever grateful to be invited into the Narmods group so that I may wait patiently for an opportunity.. Is there also a very private group for the Nipple? I have searched everywhere for it a couple months now, these are both must have pieces for any collector IMO. Anyone else that feels they are a very serious collector of rda's especially I would love to start conversing and get to know you.

 

[Mr.Mann]

I would be ever grateful to be invited into the Narmods group so that I may wait patiently for an opportunity.. Is there also a very private group for the Nipple? I have searched everywhere for it a couple months now, these are both must have pieces for any collector IMO. Anyone else that feels they are a very serious collector of RDA's especially I would love to start conversing and get to know you.

The Nipple will be back soon on Vaper's Hobby Shop. Keep checking there, but it will go FAST! I am still kicking myself for being too slow on the trigger.

 

[Mr.Mann]

Who here has an authentic Kennedy 22 with the 2x dual airflow chimneys?

 

[Mr.Mann]

I'm now a BottomFeeder...
View attachment 538807

SwampPiano with NarDA. 26ga 3mm ID 1.0 ohms

My man! Looking killer! Congrats on the beautiful piece.

 

[67Tele]

Thanks! I'm stoked!

 

[will s. flavoursnob]

The Nipple will be back soon on Vaper's Hobby Shop. Keep checking there, but it will go FAST! I am still kicking myself for being too slow on the trigger.

just joined the group very much appreciated! It certainly takes some desire and digging to get this far down the hole with some of these rare pieces thank you again.

 

[Mr.Mann]

just joined the group very much appreciated! It certainly takes some desire and digging to get this far down the hole with some of these rare pieces thank you again.

Thanks for participating. What ya' vaping on now?

 

[will s. flavoursnob]

Currently have the ax1-au atop my CritBox loving this ax1!!

 

[Mr.Mann]

Currently have the ax1-au atop my CritBox loving this ax1!!

Okay then. Send me your Crit Box and I will make you a star. Very nice, though. I got jelly all over my face.

 

[RickCain]

Who here has an authentic Kennedy 22 with the 2x dual airflow chimneys?

I do.... Just too much airflow for me so have one of the chimneys blocked on each side. Makes for a much better vape IMHO.

 

[67Tele]

Currently have the ax1-au atop my CritBox loving this ax1!!

One of these? Sector One Vapors x Vicious Ant - "AX1 +Au" Limited Edition

Very handsome piece.
And welcome!
eta: I want a Nipple too!

 

[inspects]

When you build it, make sure to not have your leads too long. It'll make more sense when you build it.

The only issue I ran into was that it does better (IMO) for dual coils with thinner wire; I got overzealous with tightening my screws and I snapped my wire a couple times. That's all you really have to be mindful of . . .

Oh, and maybe make sure that when you clip or snap off your excess leads after trapping, you don't have any wire sticking out as it may touch the top cap. That's what they were saying on the FB group, but I haven't had any issue approaching it the way I do with any other RDA. Just twist them off until they break at the trapped-point.

Got the Petri fired up tonight, made 3-mm coils, I think 4-mm would fit in there. Used 26 - 7 wraps.







Almost like this better than the NarDa's....has a tad more airflow.

 

[RickCain]

Got the Petri fired up tonight, made 3-mm coils, I think 4-mm would fit in there. Used 26 - 7 wraps.







Almost like this better than the NarDa's....has a tad more airflow.

Living mine too, other than USPS roughing up my package and shattered the glass tube which scratched the sleeve....

I do think the sleeve is just too loose on the deck making it move around way too easy.

Sent from my iPhone 6+ using Tapatalk

 

[inspects]

Living mine too, other than USPS roughing up my package and shattered the glass tube which scratched the sleeve....

I do think the sleeve is just too loose on the deck making it move around way too easy.

Sent from my iPhone 6+ using Tapatalk

Unbelievable.....where did you get it from?

 

[Mr.Mann]

Currently have the ax1-au atop my CritBox loving this ax1!!

Living mine too, other than USPS roughing up my package and shattered the glass tube which scratched the sleeve....

I do think the sleeve is just too loose on the deck making it move around way too easy.

Sent from my iPhone 6+ using Tapatalk

Ugh! Seeing that broken makes me feel ill!

 

[RickCain]

Yeah, all of the excitement of getting the package today when south the second it was in my hand and could feel stuff moving inside the box. Stupid USPS.

On a plus side, once DotMod makes the sleeve right, it vapes like a freaking dream. This is the first RDA without AFC that just is perfect for me. My Kennedy 22 is twice as loose on the draw .