RDA Round-Table Discussion and Lookout
- Thread starter Mr.Mann
- Start date
- th_trl_thread_readers 0
- Status
Whoa! Congrats, bud. So happy you finally got it and that I could hep your decision making by getting the Thump first.
But, if you want to trade . . . 
Sure, I'll trade, just not the stumpy lmao! So far so good, I like it a lot more then I did my derringer. Whyd you get rid of yours again?!Whoa! Congrats, bud. So happy you finally got it and that I could hep your decision making by getting the Thump first. [emoji23] But, if you want to trade . . .
Sent from my SM-G925V using Tapatalk
Money. At the time, I just needed the money and I THOUGHT I'd be able to easily replace that atty. Yep. Nope.
You can replace it, for another 120$ lol which I'd be hesitant to do again since no it isn't cheap, but if you did love it then I'd do it again. Now that you mention it I forgot I did ask you why you got rid of it, but my memory is fading fast, ha.
Sent from my SM-G925V using Tapatalk
Yep. It's just that it's hard to pay that money again when there's new stuff I'd like to check out. It won't hurt me now to spend it, but half of the driving force to buy an atty is typically being eager to find out if it's great. I only have half of the driving force to buy it now, and that half is that I KNOW it's a great little unit. But I can't lie, I do love the mystery of a new atty tho. That is generally the half that drives my purchases.
Heard of Drifter juice, but never seen a Drifter RDA. Can you post photos?
Where do you rank it as compared to the New Gen Post RDA's, Velocity, Narda, AX1,etc? Tough to rank for me. Not really a Competition Cloud chaser, but not a pure flavor chaser either, but it's damn good at both and machined like no other.
Last edited:
What build do you all find works best with your NoPity? Got to throw several builds at it and can't seem to get decent flavor. Vapor is nice and dense but just isn't coming close to good on flavor.
Tried:
Dual 26g 2.5m coils
Dual 24g 2.5m coils
Dual 26g 3.0m coils
Dual 24g 3.0m coils
Single 24g 4.0m coil centered
The only thing I have not done is mess with the height of the coil(s). Basically been putting them straight off the posts (not pushed up or down).
Tried:
Dual 26g 2.5m coils
Dual 24g 2.5m coils
Dual 26g 3.0m coils
Dual 24g 3.0m coils
Single 24g 4.0m coil centered
The only thing I have not done is mess with the height of the coil(s). Basically been putting them straight off the posts (not pushed up or down).
I am too haphazard to ever even remember the specs of the builds I do (most of the time, at least), but I can tell you that my coils always sit pushed down right over the coils. I mean, they are close! My ID of the coil is so small that it doesn't obstruct the airflow being pushed down like that.
Slapped in two 24g x 2.5mm coils and pushed them all the way down and it is better. Time to tinker with it to see if I can get it close to a Hobo 3.1 in flavor.
Really like the looks of this atty and it's make out of 316L SS
Hey guys so I put a few different builds in the drifter and I am getting a decent vapes ....I mean its good I'm just not getting a "wow that's good" feeling in any one area. Vapor production I know its build dependant but it has been mediocre in that respect I mean it can handle builds a bit lower and hotter then my 3.1 but not crazily so. Flavor is good(after experimenting with a few builds I was able to figure out that coil placement is KEY to getting this thing to perform) finally settled on some Clapton coils sitting slightly elevated above the side airflow just high enough to hit the lower half of the coil directly. I really want to love this thing but can't help but feel I'm not doing it right or something ..... Back to the drawing board
Last edited:
Wow that no pity is gorgeousSlapped in two 24g x 2.5mm coils and pushed them all the way down and it is better. Time to tinker with it to see if I can get it close to a Hobo 3.1 in flavor.
Really like the looks of this atty and it's make out of 316L SS
Slapped in two 24g x 2.5mm coils and pushed them all the way down and it is better. Time to tinker with it to see if I can get it close to a Hobo 3.1 in flavor.
Really like the looks of this atty and it's make out of 316L SS
I'm getting close with mine in regards to flavor but I'm not sure it will beat the Hobo for the simple fact that it's a larger chamber size. After about seven builds this last one with 2.5mm spaced 26awg SS coils a little lower than sticking straight out from the posts is working the best for me so far. I think the key is the height over the air intakes.
@Sed8op8 Go pick up the Dripbox since you like to build & do a .3 build in the Hobo or ChiNarda clone since a BF pin is available from Narmods. Best bang for the buck squonker that I've ever seen.
Is
@fishwater
Thanks hun I have the dripbox ordered and on its way ! I also have 2 Narda BF pins but I'm notbsure if it will fit the narda clone ?? Is yours a clone? Amazing layout you have there wow
Is that a VO Distro Evo Squonk ? Wow I didnt know anyone was doing those !! The Evo is turning out to be one of my faves built right it has amazing flavor and can also CLOUDz Bro if that's your thing 8)
@fishwater
Thanks hun I have the dripbox ordered and on its way ! I also have 2 Narda BF pins but I'm notbsure if it will fit the narda clone ?? Is yours a clone? Amazing layout you have there wow
Is that a VO Distro Evo Squonk ? Wow I didnt know anyone was doing those !! The Evo is turning out to be one of my faves built right it has amazing flavor and can also CLOUDz Bro if that's your thing 8)
Chowder aka Catfish (Tom) converted mine to bottom fed with a huge squonk pin. Typical magic from Tom, he'll do a send in when he has time.
@fishwater
Thanks hun I have the dripbox ordered and on its way ! I also have 2 Narda BF pins but I'm notbsure if it will fit the narda clone ?? Is yours a clone? Amazing layout you have there wow
Yep, mine is a clone. Roscoe did a run of the clones bottom fed but I don't see why the real pin wouldn't fit the clone, it looks the same to me. I may order another & try my pin from Narmods as well. If nothing else we know the pin fits the Hobo 3.1 which is becoming my favorite atty.
Chowder aka Catfish (Tom) converted mine to bottom fed with a huge squonk pin. Typical magic from Tom, he'll do a send in when he has time.
- Status
Similar threads
