How do you see it leaking? Its top air flow. And unless your blowing into the thing I doubt juice would spray in your face.
Sent from my VS986 using Tapatalk
RDA Round-Table Discussion and Lookout
- Thread starter Mr.Mann
- Start date
- th_trl_thread_readers 0
- Status
Sent from my VS986 using Tapatalk
So I officially give up on the low pro. It is literally the biggest piece of **** atty I have ever used, it almost makes the REMatty likable. I've spent the last 2 days trying to find a way to like it and I dont, so I'm throwing in the towel. No atty should make you hate it, if this is what I had to go through just to vape every time I'd quit vaping all together. Just not worth it. There's almost nothing I like about it aside from its looks.
Edit- And to top it all off my 510 pin has stripped. Nice. Real nice. I had to keep adjusting the damn thing cause the genius modder made that stupid insulator rubber so when juice gets between it and the positive block it slides all over the place........ idiots I swear. This is going straight in the garbage exactly where it belongs cause the low pro is GARBAGE. Nice 60$ blown in a little under 4 days.
Sent from my VS986 using Tapatalk
Edit- And to top it all off my 510 pin has stripped. Nice. Real nice. I had to keep adjusting the damn thing cause the genius modder made that stupid insulator rubber so when juice gets between it and the positive block it slides all over the place........ idiots I swear. This is going straight in the garbage exactly where it belongs cause the low pro is GARBAGE. Nice 60$ blown in a little under 4 days.
Sent from my VS986 using Tapatalk
Last edited:
Wow, that's really a bummer man. I appreciate the review though and will make sure no one i know buys one. So if anything, you've done a good deed by buying one and discussing your experience with it and for that i thank you.
Sent from my XT1095 using Tapatalk
Well don't let my one experience off put you from getting one, not everyone is the same or has the same outcome. If it's something you really want then by all means go for it, but would I recommend it? Hell no. I'm extremely ...... about it, it's a good thing we can't curse on this forum cause I've about ran out of words for it lol.
Sent from my VS986 using Tapatalk
I've been looking for a FLAVOR CHASING DRIPPER. I already have a few Tanks, so what I need now is a Dripper.
I could not care less about the Clouds, I think I've graduated from a Steam Train and now I'm just looking to chill. So with that said, a decent vapor producing atty but something that will throw Warm to Hot full on flavor DRIPPER.
I've been looking for a legit magma, but that's hard to find nowadays. The velocity is nice, but I'm a single coil guy. I had the Samurai Bonsai but it is just to darn small.
So, thanks guys. Hope you can give a few.
I could not care less about the Clouds, I think I've graduated from a Steam Train and now I'm just looking to chill. So with that said, a decent vapor producing atty but something that will throw Warm to Hot full on flavor DRIPPER.
I've been looking for a legit magma, but that's hard to find nowadays. The velocity is nice, but I'm a single coil guy. I had the Samurai Bonsai but it is just to darn small.
So, thanks guys. Hope you can give a few.
If you'd be willing to pay for an OG Magma, maybe you should look to the Snapdragon by Eden Mods.
Eden Mods is working on the 2nd batch of Snapdragons. As soon as they're in stock I'm ordering one. I shouldn't have procrastinated when batch #1 was in stock.
One of the most discerning vapers I know has one and he is smitten! He is the reason, or rather, his opinion of the Rose v2-s was my final straw in buying it---and that was practically a $200 RTA! So yeah, when this man says he likes something, I listen---and he loves his Snapdragon. I won't be buying one (I don't think I will), but knowing it's out there gives me a certain comfort, just in case.
Any word to what kind of builds you could fit in there? I'm a big fan of claptons and twisted builds.
I am sure twisted would work and some of the thinner ID Claptons (it's got clamps), maybe not Alien or anything like that.
So for those that like different, get a load of this:
The Earth Mod by Gforce Vapor - The Vaping Griffin
I don't know what to think of that. Kinda cool I think.That's, uh, something alright. Not sure I trust the specs on that battery. Three 3mm airholes on each side, way too airy for my tastes. It's interesting but so far out of my wheelhouse its not even funny.
It is a PITA to build. As H-berg described, the positive post insulator promotes sliding of the positive block when tightening down on the post screws. But, it delivers the best flavor I've pulled out of an atty and doesn't leak when bottom fed. Better flavor than my derringer, cyclone, or A6.
Here's a sign things are finally moving in the right direction. The Shingen rda. Two post and somewhat top air flow.
Sent from my VS986 using Tapatalk
Sent from my VS986 using Tapatalk
Ordered a Hellfire 22mm short cranked dripper just now. It's super tight airflow (1mm air hole) but the flavor is supposed to be phenomenal and I'm starting to lean toward the tighter draw anyway. I'm gonna end up a tootle puffer before all is said and done lol.
Now, THAT I'm interested in.Here's a sign things are finally moving in the right direction. The Shingen rda. Two post and somewhat top air flow.
Sent from my VS986 using Tapatalk
Random Question: I've been considering picking up a Sapor for awhile since it's so cheap, a bit more leak resistant and tends to get pretty good reviews. After seeing grimm's video, I'm pretty well sold.
What's the airflow like compared to a tugboat v2? More open, comparable, more restricted?
Sent from my XT1254 using Tapatalk
Here's a sign things are finally moving in the right direction. The Shingen rda. Two post and somewhat top air flow.
Sent from my VS986 using Tapatalk
I like that too. Couldn't find it after searching. Any more info on it?
Not really no lol I only found it by accident on instagram. Apparently this is there 2nd or 3rd prototype so I'm sure more is to change for the final design. I hope they decide to change that copper post to stainless or have the option at least.
Sent from my VS986 using Tapatalk
So I broke down and bought a thump rda; I couldn't wait any longer for reviews to show up. Will post results when it comes in.
Sent from my XT1095 using Tapatalk
Sent from my XT1095 using Tapatalk
Awesome! I look forward to your thoughts. I was actually looking at that today too, thinking about whether I want too buy one or not.
Sent from my VS986 using Tapatalk
- Status
Similar threads
