I'm a fan of the istick, but disappointed that I can't swap the battery. I got the ipv mini, but I can't lower the adjustment enough. I'm looking for a box mod with a rounded back like the above two. Specs I would like is takes a 18650 battery and I can adjust voltage down to 3 volts and of course a rounded shape. I've tried the Vamo, this is not comfortable to hold. Anyone know if they make what I'm looking for?
Rounded Box Mods
- Thread starter Mavrik1
- Start date
- th_trl_thread_readers 0
- Status
TBH I don't think such an animal exists. The Cloupor Mini only goes down as low as 3.6v like the IPVM. You are gonna need a 20w device to fire as low as 3v. But even the Hana Mini 20w only goes down to 4v. Finding that with a swappable 18650 battery might be a dead end.
I have seen conflicting specs. Some say the IPV Mini goes down to 3v, others say 3.6v. I guess the OP would know if he can't get it down to 3v.
Garemlin, that is what I'm finding too. I'll probably end up modifying my istick so I can swap batteries. There is room inside to modify it, it's got a 18650 with solder tabs in there now.
Yes sparkky1, however it won't go below 5 watts. This unit is only watt adjustable from 5-30.
Yes sparkky1, however it won't go below 5 watts. This unit is only watt adjustable from 5-30.
Not the most attractive thing with the 18650 tube, But this may be as close as you can get. or you coould just use it in 18490 mode and still have a swappable battery.
Output voltage: 1.5V--11V
1:1 ZNA 50 by Robbot Tech
Though I don't see how that is even possible when it only goes down to 7w. That would still be 3.24v at 7w on a 1.5Ω build.
yeah scratch that
Output voltage: 1.5V--11V
1:1 ZNA 50 by Robbot Tech
Though I don't see how that is even possible when it only goes down to 7w. That would still be 3.24v at 7w on a 1.5Ω build.
yeah scratch that
Last edited:
Different vaping styles my friend. I don't understand the need to go up to 20w on a 1.5Ω build but people do it. I go any higher than 13w and it tastes burnt to me.
Ya, I saw that SXMini $200 is too steep.
1:1 ZNA 50 by Robbot Tech is a bit ugly, but I'm running out of choices. I don't understand the need for high watts either, I run 3v, 1.5 ohm and I get a cloud about 10X of a cigarette and nice flavor.
I chain vape and my throat burns easy, after months of screwing around I finally have a setup that works well for me, 3v and 1.5 ohms works perfect.
1:1 ZNA 50 by Robbot Tech is a bit ugly, but I'm running out of choices. I don't understand the need for high watts either, I run 3v, 1.5 ohm and I get a cloud about 10X of a cigarette and nice flavor.
I chain vape and my throat burns easy, after months of screwing around I finally have a setup that works well for me, 3v and 1.5 ohms works perfect.
You could always buy a DNA40 board and build your own APV with one of these enclosures from Shapeways: https://www.shapeways.com/product/V...ripper-body?li=shop-results&optionId=42031067
https://www.shapeways.com/product/A...ripper-body?li=shop-results&optionId=42031044
He even has 26650 versions of the above mods.
- Status
