settings???

[MissTaggart]

Hey everyone!
I have a eVIc VTC mini and just got a CROWN tank with .25Ohm dual coil.
Any recommendations about settings?
I can use it in TC and power mode too can't I??
Which are the right settings? (i know it's depends on what I like but I'm pretty new so don't know to much about it)

Thank You

 

[BackDoc]

Dagny?

 

[MissTaggart]

guess you've read the book.....

 

[BackDoc]

Yes , not sure of the evic or crown tank( have neither, but you will get many replies) but if you can run a railroad im sure you can figure out how to run a vaporizer

 

[sawlight]

I like a restricted draw, MTL vaper, so I normally run TC around 400deg f and 30w. In wattage mode, without knowing that tank personally, I'd start at 30w and try it. If it's too warm, turn it down, want more, turn it up.
It's a curse and a blessing having all these options now! Even us veterans have to fiddle around to find our happy place, and it's different for everyone.

 

[daviedog]

Ni,,Ti,,SS for temp control.
Kanthal,,Nichrome for power..

 

[Two_Bears]

Hey everyone!
I have a eVIc VTC mini and just got a CROWN TANK with .25Ohm dual coil.
Any recommendations about settings?
I can use it in TC and power mode too can't I??
Which are the right settings? (i know it's depends on what I like but I'm pretty new so don't know to much about it)

Thank You

Nickel and Titanium wire should be used only in Temperature Control.

Kanthal and Nichrome only works in power mode.

Stainless Steel can be used in either TC or power mode.

Yes the eVic VTC Mini can be used in TC or power mode.

Don't worry About the power level for your Atomizer. Just don't burn the wick and power level to guve you a satisfying vape.

 

[Baditude]

I use the Crown tank on my RX200. It's a pretty remarkable top fill tank. I've never use the nickel coils, only the kanthal and stainless steel (0.5 and 0.125 ohm). I always use wattage/power mode on the mod, and rarely go over 30 watts. The Crown has a wide variety of air flow setting to suit your tastes.

Most important thing to remember is to "prime" your coil before you install it into any tank for the first time. This means saturating the cotton wick with e-liquid before even putting it into the tank. Don't get any e-liquid into the center air chamber. Make sure when filling the tank that you completely close off the air control, and then open it up again once the top is replaced. Watch how RIP primes the coil for this Crown tank at the 7:50 mark.

 

[MissTaggart]

I like a restricted draw, MTL vaper, so I normally run TC around 400deg f and 30w. In wattage mode, without knowing that tank personally, I'd start at 30w and try it. If it's too warm, turn it down, want more, turn it up.
It's a curse and a blessing having all these options now! Even us veterans have to fiddle around to find our happy place, and it's different for everyone.

Thank you!!

 

[BrotherBob]

Welcome and glad you joined.

 

[Dumon]

I never used tc mode before, and I have not used tanks crown, maybe others can help you

 

[Gramdogg]

From what I can find the .25 duel SS is 80-120w so max on your mod 75w should be fine. I've seen users that prefer cooler vape recommend 60-75w. You'll probably want the .5's in the future 30-80w or run in TC as 60-75w will drain your single 18650 batteries pretty fast

 

[Gramdogg]

From what I can find the .25 duel SS is 80-120w so max on your mod 75w should be fine. I've seen users that prefer cooler vape recommend 60-75w. You'll probably want the .5's in the future 30-80w or run in TC as 60-75w will drain your single 18650 batteries pretty fast