SmokTech RSST Genesis Rebuildable Atomizer

[Nomoreash]

I'm just about to order my RSST but I need to know if these wicks will work:
Stainless Steel Mesh Wicks (3 Pack) – Vapinaze

Also, I'd like to know which wire I should use. Right now I have some 32 guage Kanthal. I'm currently using a Kanger Pro tank with 2.2-2.8 ohm heads on top of a Tesla mod.

I know using the pre- rolled wicks is an expensive route, but I've just had a stroke and I'd like to keep any work minimal until I gain proper use of my right hand. Thanks.

Yes those pre-rolled wicks will work. You're 32ga wire will work fine although I prefer 30ga for regulated mods and 28g for mechanical. Lower ga is a little more durable and less springy imo but 32ga is fine.

 

[tattooed]

Wrapped some tape on the center post and its kept the juice from spilling down to the 510 connection.

Took a small oring from the the spare parts pack from an AGA T and put it on the threaded center sleeve (butted against the top of the tank) to stop juice from leaking down to the bottom of the tank. This also appears to have worked.

If these fixes hold up, I'll be quite happy with this thing.

 

[Rule62]

Wrapped some tape on the center post and its kept the juice from spilling down to the 510 connection.

Took a small oring from the the spare parts pack from an AGA T and put it on the threaded center sleeve (butted against the top of the tank) to stop juice from leaking down to the bottom of the tank. This also appears to have worked.

If these fixes hold up, I'll be quite happy with this thing.

If you have an AGA-T2 spare parts pack, you can also use the white top center post insulator on your RSST, in place of the one that came on the RSST. The one from the AGA parts hugs the center post tighter. This will stop the leaking down the post.

 

[tattooed]

I thought about that but was sure I read somewhere in here that someone tried and it didn't quite work. I'll give it a go next time I tear this thing apart.

 

[Rule62]

It worked for me. I have 3 of them I've fixed this way. I did forget to mention, put a ss washer on top of the new AGA seal. It makes the spring on the post apply even pressure on the seal.

 

[tattooed]

Good call, that's smart.

 

[StillMaticc]

I replaced the center post insulator on my RSST with the insulator from a Kanger T3 head, fits nice and tight, and I have not had a single drop of e-liquid on my 510 connector.

 

[Vash]

Im thinking of trying some SS wire rope in my RSST.Will 1.5mm or 2mm fit the RSST better? And does the 7x7 wick better than 7x19? Thanks in advance

 

[Vash]

What is best length for wick? Believe I read 35mm.Sound right?

 

[zipflint]

I'm thinking of trying this as well. I don't even know what terms to search for to get the basic understanding and safety issues clear. He|| I don't even where to buy this stuff.

 

[Vash]

Check out ss rope wick thread

 

[zipflint]

Ah. That makes sense.

Check out ss rope wick thread

 

[Vash]

I have two diff sizes on the way.Ill let you know which works best

 

[zipflint]

Cool, looking forward to your results!

I have two diff sizes on the way.Ill let you know which works best

 

[Gummy Bare]

Does anyone know where i can purchase just a top cap for the RSST? I drilled mine out and I'd rather i didn't. I want to go back to the original size air hole.

:: sent from android with tapatalk ::

 

[Uno mas]

Does anyone know where i can purchase just a top cap for the RSST? I drilled mine out and I'd rather i didn't. I want to go back to the original size air hole.

:: sent from android with tapatalk ::

The only replacement item I've seen as far is the plastic tube, sorry no help

 

[Vash]

Does anyone know where i can purchase just a top cap for the RSST? I drilled mine out and I'd rather i didn't. I want to go back to the original size air hole.

:: sent from android with tapatalk ::

http://www.e-cigarette-forum.com/fo...help-i-need-know-where-get-rsst-top-caps.html Heres a way of fixing it that might help good luck!

 

[Vash]

Cool, looking forward to your results!

So I got some of my SS rope today. Its 2mm 7x19 non galvanized and was already cleaned and burned but gave it extra burn to be safe.Wrapped a little ss mesh around top to make coil and its working great ! So much easier to wrap coil seeing that it is stiff and now my 6x12 mesh sheet will last forever Zipflint you should try it out for sure .I made more detailed post right now in rope for wick thread check it out.

 

[zipflint]

Awesome, I'll check out your post in that thread fo' sho'.

 

[Vash]

How can I make spring tighter on center post? I have drawtube and when I adjust center post to make rsst sit flush spring is so loose it wouldnt hold coil in place.Any help would be great Rsst sits flush on kts but not on. drawtube and its driving me crazy lol