SmokTech RSST Genesis Rebuildable Atomizer

[madsurgeon]

Hi guys,

Thought i'll share something i've done with my RSST.

Pulled out the insulator
View attachment 201898

inserted two 3mm silica wicks folded on themselves (3mm x 4) from below upwards. Coiled with 30awg A1. Very nice vapor and flavour. It has now become my favorite rba
View attachment 201899View attachment 201900View attachment 201901View attachment 201902

P.S: I've put in a stopper with a tiny hole in place of the fill hole stopper.
no leak so far.

 

[bigpman]

Ordered some 30 and 32 gauge kanthal some 3mm german silica wick, along with some 18500 flat tops and a nitecore i4 charger. I just need someone to have the rsst in stock and I'll be ready to try the above

Pat S.

sent from my note 2 with tapatalk 2

 

[WinchellNomNom]

Ordered some 30 and 32 gauge kanthal some 3mm german silica wick, along with some 18500 flat tops and a nitecore i4 charger. I just need someone to have the rsst in stock and I'll be ready to try the above

Pat S.

sent from my note 2 with tapatalk 2

Too bad you can't just vape your note2. It does everything else.

 

[donnah]

cloudsofvapor has them

 

[bigpman]

Too bad you can't just vape your note2. It does everything else.

Lol, that would make it perfect! All that I ordered was done right on this thing. I barely touch my laptopn and my tablet just looks pretty on the coffee table. ..

Pat S.

sent from my note 2 with tapatalk 2

 

[dirtydog2008]

is the neg post wire suppose to glow i heard it is because it has a insulater the rest of the coil is glowing except that need help THANKS

 

[thebong24]

Hi guys,

Thought i'll share something i've done with my RSST.

Pulled out the insulator
View attachment 201898

inserted two 3mm silica wicks folded on themselves (3mm x 4) from below upwards. Coiled with 30awg A1. Very nice vapor and flavour. It has now become my favorite RBA
View attachment 201899View attachment 201900View attachment 201901View attachment 201902

P.S: I've put in a stopper with a tiny hole in place of the fill hole stopper.
no leak so far.
View attachment 201903

That looks great!!!

sent from mars

 

[StaircaseWit]

is the neg post wire suppose to glow i heard it is because it has a insulater the rest of the coil is glowing except that need help THANKS

That refers to the coil glowing when trying to pulse a coil to get it to oxidize a wick. If the coil is glowing evenly, from the middle out, and the top and bottom 'leg' that goes to the terminals isn't, you've got a good coil.

 

[dirtydog2008]

thanks staircaseWit but whats happen if my wick is oxidized and the bottom neg leg glows

 

[StaircaseWit]

thanks staircaseWit but whats happen if my wick is oxidized and the bottom neg leg glows

Then your coil needs adjusting. Pulsing it on a mechanical mod will make it a lot easier.

Search for eHuman's blog. He explains everything you need to know pretty well. Or watch pbusardo's setup video, although he's a bit clumsy.

 

[Flow]

RSST on order here...

This long post starts to scare me a bit... is it complicated to get it right?

 

[Andy Thatcher]

Next to Zens probably the easiest set up there is.

I popped a single folded 3mm silica wick in mine two days ago. No wicking issues. Still think I prefer mesh or mesh covered rope but thought I would give it a go

Sent from my SAMSUNG-SGH-I727 using Tapatalk 2

 

[madsurgeon]

thanks staircaseWit but whats happen if my wick is oxidized and the bottom neg leg glows

Hi,
i try and keep the lengths of both ends of the coil as even as possible and spread out the coil configuration evenly before i start checking for hot spots. The moment the hot spot appears, i start massaging it down or up depending on location until the other coils light up. From there on its easy. Once all the coils are lit,i massage the coils to fit snug on the wick and the excess gets folded towards the respective posts. This way my coils last a really long time.

 

[Ink Stained]

Just got one of these in and it is pretty awesome other than the small air hole. I just set it up to a 1.7 so I could use it on a VW, but later I am going to set it up with a lower res and see how well it does. ON a side note. Had 3 brand new Ceramic wicks. Broke all 3 trying to snap them off to size. Anyone using ceramic know a simple way to get these down to size without getting cracking? Or a vendor that has them in stock at the moment. Not going to attempt fish wick as I dont have the patients to do so.

 

[-brandon-]

Diamond cut off wheel works best for cutting / shaping the porous ceramic.

BTW, you should be fine using a "shorty" as long as it goes into the tank - even a little - you're good. You can kinda see in this photo that my wicks are barely going into the tank.

 

[Nomoreash]

ON a side note. Had 3 brand new Ceramic wicks. Broke all 3 trying to snap them off to size. Anyone using ceramic know a simple way to get these down to size without getting cracking? Or a vendor that has them in stock at the moment. Not going to attempt fish wick as I dont have the patients to do so.

I used pliers with mine. just snip the end a little at a time till you get it where you need it, don't try to take to much with each crimp. Hold the wick as close as possible to the end your snipping.

I've read Discount Vapers is supposed to be getting some in soon and Tank still has some I think, although at a higher price.

 

[Ink Stained]

Thanks guys. I knew that I would get the answer here. Ill check tank. Never heard of them. Hopefully they are a big enough vendor that they show up in google.
And....I threw away the shorties not knowing any better. Go Figure haha

 

[plastictree]

Hey guys, I just got my rsst today, and I'm having a hot leg problem with the negative connection. Anyone else have this problem? It's a .7 ohm coil on a battery that is half charged

 

[StaircaseWit]

Hey guys, I just got my rsst today, and I'm having a hot leg problem with the negative connection. Anyone else have this problem? It's a .7 ohm coil on a battery that is half charged

How did you wrap the coil? Is it making good contact with the wick without being too tight and diggin in? How did you roll your wick? Did you pre-oxidize, or are you trying to pulse?

Short answer: pulse and prod the coil. Spin the wick around a bit inside the coil. Pulse some more, move the wick around until it glows evenly. Do all this dry. Don't add any juice until the coil glows perfectly from the middle out.

 

[plastictree]

I hand wrapped the wick while it was on the mod while spinning the mod to wrap it, it was lightly oxidized and then pulsed to glow evenly. I glowed evenly with no juice, but it seems like the throw is too far, but I'm about to wrap a higher ohm coil with 32 gauge and see, but idk