Snails - Response on Threads Part 7

[oldbikeguy]

Also say - hypothetically - the tightening nut(s) will NOT budge and/or are now rounded off.

This might also work
http://www.summitracing.com/parts/shc-94772?seid=srese1&gclid=CPy0npT6w8wCFRIbgQodss4KlA

 

[oldbikeguy]

sucks

Yep that about sums it up !!

 

[Katmar]

Chat w/ @Katmar. She is saying 90 days for anything "new".

She's making me have a cow.

Sorry, Honey, don't mean to have you have a cow. The liquids on the market right now will continue to be sold for the next 2 years and 30 days before the rules go into effect. Any NEW flavors or equipment that comes out AFTER 90 days will be subject to the new rules. So, your flavors are good to be sold to you for 2 years and 30 days. Hope that helped. Same goes with the gear. So sorry if I confused you. I didn't mean to.

 

[SilverBear]

Bear when we set sleeve anchors we drill the holes extra deep just for that reason then if needed we saw them off and knock them down flush or lower and fill the holes if needed,are they in concrete ?

The holes are completely through the deck floor (wood).

 

[SilverBear]

This might also work
http://www.summitracing.com/parts/shc-94772?seid=srese1&gclid=CPy0npT6w8wCFRIbgQodss4KlA

If all else fails. Gonna haul out the mega channel-locks and an
old tire iron. Or hammer and chisel. Then just wham 'em with
a set punch down into the under-deck darkness.

 

[AttyPops]

OK, OBG... say - hypothetically - there are six (6) of those ^ anchoring the current umbrella.

Also say - hypothetically - the tightening nut(s) will NOT budge and/or are now rounded off.

Is my only choice - hypothetically - now drilling them out???

(Yes... new umbrella on the way.)

Get a cutting wheel (disc on a hand drill)* and cut off the nut. Or...if it's in a safe place for fire...heat the nut and turn it off. Could try penetrating oil too (runs and stains), and vise-grips.

* wear eye protection

 

[AttyPops]

flyby...hi snails.

 

[tiburonfirst]

~~~~ @ that flying pops!

 

[Katya]

Get a cutting wheel (disc on a hand drill)* and cut off the nut.

Hmmm. I might need that. I'd like to cut off some nuts right now.

Passing through!

 

[daleron]

might have to be fb, bear!

it's disturbing though - i believe ads are gonna be a no,no and that's what pays the servers here

No!!!


We need to drown our sorrows ...

 

[Katya]

What say y'all???...
Deeming Regulations have been released!!!!

See my post above..

 

[SilverBear]

... vise-grips ...

:: duh :: me ... VISE GRIPS ... not channel locks!!!

 

[Katya]

lots of grey area there, bear! will a new concoction trigger fda approval first? who knows - from the little i saw there's plenty of room for confusion .......... sigh

Not only that. The Congress has to approve those new regs before they become law.

I just wonder if ECF can even survive in the long run without ads?

 

[SilverBear]

Get a cutting wheel (disc on a hand drill)* and cut off the nut.

That's another option. I'll try a couple no-cost things first.

 

[tiburonfirst]

hiya, tweety!

 

[SilverBear]

Thank you!

 

[tiburonfirst]

Not only that. The Congress has to approve those new regs before they become law.

I just wonder if ECF can even survive in the long run without ads?

what was the grace period there? i know there's very little of proof of age ...............

 

[tiburonfirst]

Not only that. The Congress has to approve those new regs before they become law.

I just wonder if ECF can even survive in the long run without ads?

i doubt it

 

[tiburonfirst]

at least dale did the right thing tonight!

 

[Katya]

i doubt it

Please don't tell me that I'll have to join FB to stay in touch with my vaping friends.